43826

Philips FC8710 Manual

11
Zoom out
Zoom in
Previous page
1/72
Next page
Caution: Always make sure the lter is present inside the dust container. If you use the robot
without the lter inside the dust container, the motor will be damaged.
Cleaning sensors, wheels and side brushes
To maintain good cleaning performance, you have to clean the drop-off sensors, the wheels and the
side brushes from time to time.
1 Make sure the power switch is in ‘off’ position.
2 Place the robot upside down on a at surface.
3 Use a brush with soft bristles (e.g. a toothbrush) to remove dust or uff from the drop-off
sensors. Also check if there is any dirt or uff blocking the suction opening (Fig. 42).
Note: It is important that you clean the drop-off sensors regularly. If the drop-off sensors are dirty,
the robot may fail to detect height differences.
4 Use a brush with soft bristles (e.g. a toothbrush) to remove dust or uff from the front
wheel and side wheels (Fig. 43).
5 To clean the side brushes, grab them by the bristles and pull them off their shafts (Fig. 44).
6 Remove uff, hairs and threads from the shaft and from the side brush with a soft brush
(e.g. a toothbrush) or a cloth (Fig. 45).
7 Check the side brushes and the bottom of the robot for any sharp objects that could damage
your oor.
Replacement
You can order spareparts and accessories at www.shop.philips.com/service or at your Philips
dealer. You can also contact the Philips Consumer Care Centre in your country.
Replacing the lter
Replace the lter if it is very dirty or damaged. You can order a new lter under order number
CP0108. See ‘Emptying and cleaning the dust container’ in chapter ‘Cleaning and maintenance’ for
instructions on how to remove the lter from the dust container and how to place it in the dust
container.
Replacing the side brushes
Replace the side brushes after some time to ensure proper cleaning results.
Note: Always replace the side brushes when you notice signs of wear or damage. We also recommend
that you replace both side brushes at the same time. You can order spare side brushes as a set under
order number CP0107.
1 Make sure that the on/off switch is in ‘off’ position.
2 To replace the side brushes, grab the old side brushes by the bristles and pull them off their
shafts.
3 Push the new side brushes onto the shafts (Fig. 11).
ENGLISH 11
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips FC8710 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips FC8710 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Philips FC8710

Philips FC8710 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 84 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info