478674
10
Zoom out
Zoom in
Previous page
1/15
Next page
1.
The
Head
(Fig.
12).
Open
the
hinged
face
cover
plate.
2.
The
Arm
(Fig.
13).
Lubricate
all
points
marked
thus
0.
3.
The
Needle
Plate.
Take
out
the
screws
and
remove
the
plate.
4.
The
Hook
(Fig.
14).
Move
the
needle
bar
to
its
high
est
and
tilt
the
head
over
on
its
hinges.
With
a
small
brush
dust
the
hook.
Apply
a
few
drops
of
paraffin
to
the
race
between
the
hook
II
and
the
bobbin
carrier
IV;
then
work
the
mach
ine
rapidly
for
a
short
while.
Now
apply
a
few
drops
of
oil.
Should
this
prove
inef
fective
in
dislodging
any
dirt
from
the
hook,
or
should
thread
ends
impede
the
free
move
ment,
then
the
hook
must
be
carefully
dis
mantled.
This
is
done
by
removing
the
race
guide
Ill,
after
the
small
screws
1,
2
and
3
have
been
taken
out.
Now
the
bobbin
carrier
IV
can
be
removed.
All
dismantled
parts
should
be
carefully
wiped
with
a
clean
rag.
Before
reassembling
the
parts
move
the
thread
take-up
lever
to
.
.
Fig.
16
its
highest
point
so
that
the
point
I
of
the
hook
is
on
the
left,
and
on
top,
as
shown
in
Fig.
14.
Then
re
place
the
bobbin
carrier
IV
into
the
hook
II,
and
let
the
retaining
key
engage
into
the
groove
n
see
Fig.
14.
Finally,
replace
the
guide
Ill
and
fix
it
down
with
screws
1,
2
and
3.
You
must
also
lubricate
all
Fig.
17
other
points
indicated
in
the
illustrations,
making
sure
that
after
oiling
oIl
ports
ore properly
replaced.
Ii’
Fig.
14
Fig.
15
Fig.
18
View
of
Underside
of
Machine
Bedplote
16
17
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pfaff 132 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pfaff 132 in the language / languages: English as an attachment in your email.

The manual is 0,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info