770990

Petsafe PIF00-15002 Manual

8
Zoom out
Zoom in
Previous page
1/24
Next page
1-800-732-26778
Step 2: Prepare the Receiver Collar
Your Receiver Collar comes with short Contact Points installed. Use the Long Contact Points for
pets with long or thick hair. Tighten the Contact Points using the Contact Point Wrench (2A). Check
tightness weekly.
Insert and Remove the Receiver Collar Battery
Note: Do not install the battery while the Receiver Collar is on your pet.
This Receiver collar utilizes a replaceable PetSafe® battery (RFA-67). This unique battery is designed to
make battery replacement easier and increase water protection. Once you insert the battery and turn it
to the lock position, the unit will be turned ON.
To insert the battery, align the symbols on the battery (arrow) and Receiver Collar (triangle) (2B). Use
the edge of the Test Light Tool (2B) to turn the battery clockwise until the arrow lines up with the lock
symbol on the housing.
To remove the battery, turn the battery counter-clockwise using the edge of the Test Light Tool (2C).
DO NOT attempt to cut into or pry open the battery. Be sure to discard the used battery properly.
Risk of explosion if batteries are replaced by an incorrect type. Do not short
circuit, mix old and new batteries, dispose of in fire, or expose to water. When
batteries are stored or disposed, they must be protected from shorting. Dispose
of used batteries properly.
Note: Before replacing the battery, discharge all power by holding the Mode Button at least 30
seconds until the LED is no longer illuminated.
A replacement PetSafe® battery (RFA-67) can be found at many retailers. Contact the Customer Care
Center at 1-800-732-2677 or visit our web site at www.petsafe.net to locate a retailer near you.
Turn the Receiver Collar ON
Press and hold the Mode Button continuously for 5 seconds (2D) The green or red Receiver Indicator
Light will turn ON for 5 seconds (2E) to indicate battery status, followed by the red Receiver Indicator
Light flashing the Static Correction level settings.
Turn the Receiver Collar OFF
Press and hold the Mode Button continuously for 5 seconds. The red Receiver Indicator Light will be
ON during this time. The red Receiver Indicator Light will then turn OFF and all Receiver Indicator
Lights will stay OFF indicating that the unit is turned OFF.
Set the Static Correction Level
Read all steps before attempting to set the Static Correction Level.
1. Press the Mode Button and release (2D) when the Receiver Indicator Light illuminates Red (2E).
2. The Receiver Indicator Light will emit a series of red flashes representing the Static Correction Level.
3. Increase the Static Correction Level by pressing and releasing the Mode Button within 5 seconds
of the previous series of flashes.
The Static Correction Levels increase in strength from 1 to 6. Pushing the Mode Button while the
Receiver Collar is on Level 6 will cause the Receiver Collar to revert to Level 1. Refer to the Function
and Response Table to choose the Static Correction Level that best fits your pet.
Mode
Button
2E
2D
2C
2B
2A
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Petsafe PIF00-15002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Petsafe PIF00-15002 in the language / languages: English as an attachment in your email.

The manual is 2.14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info