742528

PerfectPro WS2BT - WORKSTATION 2 Manual

10
Zoom out
Zoom in
Previous page
1/50
Next page
Bluetooth LED conguration
1. Press the On/Off button to turn on the radio.
2. Press the Menu button, and then rotate the Tuning knob until the display shows
“System”.
3. Press the Tuning knob; rotate the Tuning knob until the display shows “Bluetooth
LED”.
4. Press the Tuning knob to enter the Bluetooth LED adjustment menu.
5. Rotate the Tuning knob to select “on” (by default) in order to keep Bluetooth LED
lightened when connected;
6. Or rotate the Tuning knob to select “off” to turn off Bluetooth LED when Bluetooth
connection has been established.
7. Press the Tuning knobtoconrmyourchoice.
CHARGING A MOBILE PHONE
The USB socket on the left side can provide DC power of 5V/0.5A for charging a mobile
phone. Connect the mobile phone to the USB socket with an appropriate cable (not
included with this radio). The USB power is available in all modes, including standby
mode.
Refer to the user manual or the manufacturer of the mobile phone to verify if it supports
charging from an USB power.
The USB socket is suitable for DC power-out only and cannot be used for e.g. playback
of music from a USB stick.
Warning: Never use the USB socket in rainy or moist conditions to prevent moist from
entering the radio and so to prevent potential short circuit. Always keep the rubber cover
well closed under these conditions.
It is recommended to use AC power while charging a mobile phone via USB socket. On
DC power it is also possible to charge a mobile phone from the USB socket, however
using DC power to charge a mobile phone will consume energy from the batteries and
so drain the batteries easily.
OPERATING THE RADIO – AUX IN
A 3.5mm stereo Aux In socket is provided on the side behind the rubber cover, for
connecting an external audio device such as MP3 player or CD player (not included).
1. Connect a stereo or mono audio source to the Aux In socket.
2. Press the Source button to select AUX input. Display will show “AUX IN”.
3. Play the external player.
4. Adjust the volume of both the radio and the player for comfortable listening.
Notes: Never use the Aux-In socket in rainy or moist conditions to prevent moist from
entering the radio. Keep the rubber cover well closed under these conditions.
The Auto-Power management function will be activated in AUX IN mode. If there
is no signal* from the Aux-In socket for a period of over 15 minutes, the radio will
automatically switch to standby mode. Pressing the On/Off button will wake up the unit.
15 16
* Also when the incoming signal from the external device is too low and cannot be
detected for a period of over 15 minutes by the Auto-Power management, the radio will
switch to standby mode.
To prevent this raise the output level of the external device enough to be detected.
LOUDNESS
The Loudness function enables to get compensation on lower and higher frequency.
The effect will be more audible when the radio is on a lower volume level (Dynamic
Loudness).
1. Press the On/Off button to turn on the radio.
2. Press the Menu button, and then rotate the Tuning knob until the display shows
“System”.
3. Press the Tuning knob; rotate the Tuning knob until the display shows “Loudness”.
4. Rotate the Tuning knob to select between “Loudness On” or “Loudness Off”. Press
the Tuning knobtoconrmthesettingandreturntonormaldisplay.
TONE
The Tone function enables the user to adjust the lower and higher sound frequencies.
1. Press the On/Off button to turn on the radio.
2. Press and hold the Volume knob for about 3 seconds, the display shows “BASS 0”.
3. Rotate the Volume knob to set the desire Bass level.
4. Press the Volume knobtoconrm,thedisplayshows“TREBLE0”.
5. Rotate the Volume knob to set the desire Treble level.
6. Press the Volume knobtoconrmandreturntonormaldisplay,
METAL TELESCOPIC ANTENNA
You can use this as an alternative antenna for your radio in areas or locations where the
radio signal (FM/DAB/DAB+) is weak to very weak.
ATTENTION: The standard antenna on the radio is exible. The metal antenna
is not exible or bendable and should be used with care. Breaking or bending
antennas is not covered by warranty.
Installing:Carefullyscrewoffthestandardexibleantenna.Firstcarefullyloosenthe
antenna with an open-end-wrench key (size 14) – turn counter clockwise. Carefully
screw on the metal telescopic antenna and softly tighten it with an open-end-wrench key
(size 14) – turn clockwise.
ATTENTION: do not use too much force when xing the antennas as this can
damage the screw threat of the antennas or make it break off
GB
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for PerfectPro WS2BT - WORKSTATION 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of PerfectPro WS2BT - WORKSTATION 2 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info