Manual PerfectPro Workstation (page 7 of 36) (English, German, Dutch, French)

742531

Zoom out

Zoom in

1/36

11 12

Scan sensitivity setting – FM

The radio will normally scan all stations from FM broadcasts including the weaker

signals.However,youmaywishtheAuto-scantondonlythosestationswithstrong

enough signals to give good reception.

1. Press the On/Off button to turn on the radio.

2. Select the FM band by pressing the Source button.

3. Press the Menu button, the display shows “Scan setting”.

4. Press the Tuning knob.

5. Rotate the Tuning knob to select between “All stations” or “Strong station”

 (defaultis“Allstations”).The“Strongstation”optionwillallowtheradiotond

strong signals only when scanning.

6. Press the Tuning knobtoconrmyoursetting.Thedisplaywillreturnto 

normal radio display.

PRESET STATIONS

Storing preset stations

There are 20 memory presets in the radio, 10 for DAB and 10 for FM. Presets are

remembered by the radio in the event of a power failure.

1. Press the On/Off button to turn on the radio.

2. Press the Source button to select the desired waveband.

3. Tune to the required station.

4. Press and hold the required Preset button until the radio beeps and shows “Saved”.

5. Repeat step 3 and 4 for the remaining presets.

6. Stations stored in the preset memories can be over-written by following the

above procedure.

Recalling preset stations

1. Press the On/Off button to turn on the radio.

2. Press the Source buttontoselectthedesiredwaveband.BrieyPresstherequired

Preset button.

3. In FM mode the display will show for example ”P1” on top right hand side.

MANUALLY SETTING CLOCK

The clock can only be manually set when the radio is in standby mode. If no buttons are

pressed for 5 seconds, the radio will exit the clock setup and the setting is cancelled.

1. PressandholdtheTimeSetknobfor12secondsuntilthehourdigitsashonthe

display.

2. Rotate the Time Set knob to set the hour.

3. Press the Time Set knobtoconrm,theminutedigitsash.

4. Rotate the Time Set knob to set the minute.

5. Press the Time Set knobtoconrm,thedayashesonthedisplay.

6. Rotate the Time Set knob to set the current day.

7. Press the Time Set knobtoconrm,themonthashes.

8. Rotate the Time Set knob to set the current month.

9. Press the Time Set knobtoconrm,theyearwillthenashonthedisplay.

10. Rotate the Time Set knob to set the current year.

11. Press the Time Set knobtoconrm,“SYNCLOCKON”ashes.

12. Rotary the Time Set knob to select “SYNCLOCK ON” or “SYNCLOCK OFF”.

13. Press the Time Set knobtoconrmandnishtheclocksetting.

RDS time synchronisation

If “SYNCLOCK ON” is selected, the symbol “ ” will show on the clock display. Some

RDS stations transmit a time signal. If reception is good and you have selected the

“SYNCLOCK ON” option during the time setting, the time will be automatically updated

(“ ”ashesonthedisplay).Timesynchronizationcantakeseveralminutes.The

automatic time setting is always activated when the radio is switched from standby to

FM broadcasting and receives a RDS station.

OPERATING THE RADIO – AUX IN

A 3.5mm stereo Aux In socket is provided on the side behind the rubber cover, for

connecting an external audio device such as MP3 player or CD player (not included).

1. Connect a stereo or mono audio source to the Aux In socket.

2. Press the Source button to select AUX input. Display will show “AUX IN”.

3. Play the external player.

4. Adjust the volume of both the radio and the player for comfortable listening.

Notes: Never use the Aux-In socket in rainy or moist conditions to prevent moist from

entering the radio. Keep the rubber cover well closed under these conditions.

The Auto-Power management function will be activated in AUX IN mode. If there

is no signal* from the Aux-In socket for a period of over 15 minutes, the radio will

automatically switch to standby mode. Pressing the On/Off button will wake up the unit.

* Also when the incoming signal from the external device is too low and cannot be

detected for a period of over 15 minutes by the Auto-Power management, the radio will

switch to standby mode.

To prevent this raise the output level of the external device enough to be detected.

LOUDNESS

The Loudness function enables to get compensation on lower and higher frequency.

The effect will be more audible when the radio is on a lower volume level (Dynamic

Loudness).

1. Press the On/Off button to turn on the radio.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of PerfectPro Workstation in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,32 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

PerfectPro Workstation Manual

Product: