742531

PerfectPro Workstation Manual

6
Zoom out
Zoom in
Previous page
1/36
Next page
9 10
GB
GB
Finding new stations – DAB
Fromtimetotime,newstationsmaybecomeavailable.Youmayproceedtondnew
stations as follows:
1. In DAB mode, press the Menu button, “Full scan” shows on the display.
2. Press the Tuning knob, the radio will perform a scan of the Band III DAB
channels. As new stations are found, the station counter on the right-hand side of
the display will increase and new radio stations found will be added to the list stored
in the radio.
Manual Tuning – DAB
Manualtuningisanalternativemethodofndingnewstations.Insteadofscanningthe
entire Band III channels automatically, you may tune the radio directly to a known DAB
channel and store all the multiplex in that channel into the available station list.
1. In DAB mode, press the Menu button and rotate the Tuning knob until the LCD
display shows “Manual Tune”, then press the Tuning knob. The display will show
DAB channel and Frequency.
2. Rotate the Tuning knob to select the desired channel or Frequency and press the
Tuning knob to tune to the chosen frequency.
3. When DAB stations in the tuned channel are found, the display will show the
name of the station. Any new radio stations found will be added to the list stored in
the radio.
4. Thesignalstrengthdisplayshowsthereceptionofthestation.Theclearunlled
rectangle indicates minimum signal level required for satisfactory reception. The
signal strength bars will go up or down showing the changing signal strength as you
adjust the antenna or the position of the radio.
5. Repeat step 1 to 4 for other channels with new stations.
6. Press the Menu button twice to exit manual tuning and return to normal
DAB operation.
Dynamic Range Control (DRC) settings – DAB
DRC can make quieter sounds easier to hear when your radio is used in a noisy
environment.
1. In DAB mode, press the Menu button and rotate the Tuning knob until “DRC
value” appears on the display, press the Tuning knob.
2. Rotate the Tuning knob to select required DRC setting (default is OFF).
DRC off DRC is switched off, broadcast DRC will be ignored.
DRC high DRC is set as sent by broadcaster.
DRC low DRC level is set to 1/2 that sent by broadcaster.
3. Press the Tuning the knobtoconrmthesetting.Thedisplaywillreturntonormal
radio display.
Note: Not all DAB broadcasts are able to use the DRC function. If the broadcast does
not support DRC, then the DRC setting in the radio will have no effect.
FM MODE
Operating the radio – FM seek station
1. Press the On/Off button to turn on the radio.
2. Select the FM waveband by pressing the Source button.
3. IfthisisthersttimetoswitchtoFMmode,thestationinpreset1willbeplayed.If
the radio has been used before, the last listened station will be played.
4. To seek station, press the Tuning knob.Thescanstopsautomaticallywhenitnds
astationofsufcientstrength.
5. After a few seconds, the display will update and show station name if RDS
information is being received.
6. Tondthenextstation,presstheTuning knob again.
7. To seek stations in an opposite direction, rotate the Tuning knob clockwise (to scan
from low frequency to high frequency) or rotate counter clockwise (to scan from
high frequency to low frequency), and press the Tuning knob.
8. When the waveband end is reached, the radio will recommence tuning from the
opposite waveband end.
Manual tuning – FM
1. Press the On/Off button to turn on the radio.
2. Select the FM band by pressing the Source button.
3. Rotate the Tuning knob to reach the preferred FM station. The radio will change
the frequency in steps of 50 kHz.
4. Rotate the rubber antenna to get the best reception. If the radio is tuned to a
stationofsufcientsignalstrengthwithRDSinformationpresent,thedisplaymay
change to show the station name. 5. When the waveband end is reached, the radio
will recommence tuning from the opposite waveband end.
RDS station service – FM
RDS (Radio Data System) is an information system which inaudible digital information
is transmitted in addition to the normal FM radio program. When the radio is receiving a
RDSstationandthereceptionstrengthissufcient,thestationnamewillappearinthe
display. It may take some time before the RDS information is available.
Calling up RDS information
When you are listening to a FM station with RDS system, repeatedly press the Info
button to cycle through the information. This will only function if the reception level is
sufcientandclear.
a. Radio text (RT) Displays the message about the station being listened to as
ticker text.
b. Program type (PTY) Displays the type of station being listened to, e.g. Pop, Classic,
News, etc.
c. Frequency Displays the frequency of the station being listened to.
d. Stereo or Mono Displays Stereo or Mono.
e. Signal level Displays the signal strength.
f. Time & date Displays the current time (24 hour clock) and date.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for PerfectPro Workstation at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of PerfectPro Workstation in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info