742384

PerfectPro Bull1 - Rockbull Manual

7
Zoom out
Zoom in
Previous page
1/40
Next page
9 10
GB
GB
Calling up RDS information
When you are listening to a FM station with RDS system, repeatedly press the INFO
button to cycle through the information. This will only function if the reception level is
sufcientandclear.
a. Stationname(PS) Displaysthenameofstationbeinglistenedto.
b. Radiotext(RT) Displaysthemessageaboutthestationbeinglistenedtoas
ticker text.
c. Programtype(PTY) Displaysthetypeofstationbeinglistenedto,e.g.Pop,
Classic, News, etc.
d. Frequency Displays the frequency of the station being listened to.
e. Stereo or Mono Displays Stereo or Mono.
f. Signal level Displays the signal strength.
g. Time&date Displaysthecurrenttime(24hourclock)anddate.
Scan sensitivity setting – FM
The radio will normally scan all stations from FM broadcasts including the weaker
signals.However,youmaywishtheAuto-scantondonlythosestationswithstrong
enough signals to give good reception.
1. Press the On/Off button to switch on the radio.
2. Select the FM band by pressing the SOURCE button.
3. Press the MENU button, the display shows “Scan Setting”.
4. Press the TUNING button.
5. Rotate the TUNING knob to select “All Stations” or “Strong Station” (default is “All
Stations”).The“StrongStation”optionwillallowtheradiotondstrongsignalsonly
when scanning.
6. PresstheTUNINGknobtoconrmyoursetting.Thedisplaywillreturntonormal
radio display.
FM stereo / mono
1. If the FM station being received is weak, some hiss may be audible. To reduce
the hiss, press the Mono/Stereo button to switch to mono mode, the display will
show “Mono”.
2. To return to stereo mode, press the Mono/Stereo button and the display shows
“Stereo”, the radio will switch to stereo mode automatically if the reception is good.
3. “Mono” and “Stereo” can be displayed on the LCD display (See “Calling up RDS
information”above)
PRESET STATIONS
Storing preset stations
There are 20 memory presets in the radio, 10 for DAB and 10 for FM. Presets are
remembered by the radio in the event of a power failure.
1. Press the On/Off button to switch on the radio.
2. Select the desired waveband by pressing the SOURCE button.
3. Tune to the required station.
4. Press and hold the required Preset(1–10)buttonuntiltheradiobeepsandshows
“Saved”.
5. Repeat step 3 and 4 for the remaining presets.
6. Stations stored in the preset memories can be over-written again by following the
above procedures.
Recalling preset stations
1. Press the On/Off button to switch on the radio.
2. Select the desired waveband by pressing the SOURCE button.
3. BrieyPresstherequiredPreset(1-10)button.InFMmodethedisplaywillshow
for example ”P1” on top right hand side.
AUX-IN MODE
A 3.5mm stereo Aux-In socket is provided on the side behind the rubber cover, for
connecting an external audio device such as MP3 player or CD player (Aux cable not
includedwiththisradio).
1. Connect an audio source to the AUX-IN socket.
2. Press the SOURCE button to select AUX input. Display will show “AUX IN”.
3. Play the external player.
4. Adjust the VOLUME of both the radio and the player for comfortable listening.
5. After use, close the rubber cover to prevent moist or dust from entering into the
sockets and radio.
Notes: Never use the Aux-In socket in rainy or moist conditions to prevent moist from
entering the radio. Keep the rubber cover well closed under these conditions.
The Auto-Power management function will be activated in AUX mode. If there is no
signal* from the Aux-In socket for a period of over 15 minutes, the radio will automatically
switch to standby mode. Pressing the On/Off button will wake up the unit.
* Also when the incoming signal from the external device is too low and cannot be
detected for a period of over 15 minutes by the Auto-Power management, the radio will
switch to standby mode.
To prevent this raise the output level of the external device enough to be detected.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for PerfectPro Bull1 - Rockbull at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of PerfectPro Bull1 - Rockbull in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info