622426
9
Zoom out
Zoom in
Previous page
1/80
Next page
EVM892
29.04.2010 ©Velleman nv
9
Limits of the meter:
FUNCTION RED LEAD
CONNECTION
INPUT LIMITS
200mV VHz 250V DC or rms AC
V & V VHz 600V DC, 600V AC (sine wave)
Hz VHz 250V DC or rms AC
VHz 250V DC or rms AC
/ VHz 250V DC or rms AC
mA & mA mA/temp/CAP/hFe 200mA DC or rms AC
10 & 10A 10A 10A DC or rms AC
for max. 10 seconds
Measuring voltages
Connect the black test lead to the "COM" jack and the red test lead to the
"VHz" jack.
Select the appropriate V (DC voltage)or V (AC voltage) range with the
FUNCTION switch. When the range is unknown, always select the highest
possible range and lower to the appropriate range.
Connect the test probes to the circuit under test.
The measured value appears on the display.
Notes:
For DC-measurements: when a negative polarity is present at the red test
lead, the indicated value is preceded by a “-” sign.
When the measured value is higher than the selected range limit, the display
will show “1”. Select a higher range.
Measuring currents
Do not measure current in circuits with voltages > 250V
Current measurements: mA/TEMP/CAP/hFE jack max. 200mA; for
measurements up to 10A use the 10A jack. When measuring currents up
to 10A, max. 10s continuous measurement followed by a 15 minutes break
between 2 measurements.
Always be careful when working with voltages above 60Vdc or 30Vac rms.
Keep your fingers behind the probe barriers at all times during
measurement.
Connect the black test lead to the "COM" jack and the red test lead to the
"mA/TEMP/CAP/hFE" jack for measurements of max. 200mA or to "10A" jack for
measurements of max. 10A.
Select the appropriate A (DC) or A (AC) range with the FUNCTION switch.
Select the 200m/20m10 range when the red test lead is connected to the
"mA/TEMP/CAP/hFE" jack; select the 20m10 range when the red test lead is
connected to the "10A" jack. When the range is unknown, always select the
highest possible range and lower to the appropriate range.
Connect the test probes in series with the circuit.
Read the measured value from the display.
Notes:
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Perel EVM892 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Perel EVM892 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 0,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info