622426
8
Zoom out
Zoom in
Previous page
1/80
Next page
EVM892
29.04.2010 ©Velleman nv
8
Replace the fuse (ceramic – high breaking capacity 5x20mm F10A/250V)
Place the PCB back. Make sure the LCD connection, buttons and jacks are lined
up. Tighten the 4 screws.
Close the housing and tighten the 3 screws. Put the protective cover back.
8. Accessories
Set test probes 10A CAT II 600V
Thermo couple type K, RVS probe (max. 400°C)
Battery (inside meter)
User manual
Adaptor socket for easily measuring transistors and capacitors, and to connect
thermocouples.
Cover: protects the meter and provides a comfortable grip. For positioning
features, refer to the images on page 2 of this manual.
A & B: Use either the small or large foldable stand
C: Use the small stand to hang the meter to a wall: remove the small stand and
insert it in the slots near the top of the cover. Drive a nail in the wall and
hang the meter.
D: The test probes can be stored in the two provisions at the back.
9. Operating instructions
Risk of electric shock during operation. Be very careful when
measuring live circuits.
Before measuring, always make sure the meter and/or test probes
are not damaged and verify the connections, selected function and
range.
Never exceed the limit value for protection. This limit value is listed separately
in the specifications for each range of measurement.
Do not touch unused terminals when the meter is linked to a circuit which is
being tested.
Only use the meter in the indicated overvoltage/installation category. Never
measure voltages that might exceed the indicated category values.
Disconnect the test leads from the tested circuit before rotating the range
selector in order to change functions.
When carrying out measurements on a TV set or switching power circuits,
always remember that high amplitude voltage pulses at the test points might
damage the meter.
Always be careful when working with voltages above 60Vdc or 30Vac rms. Keep
your fingers behind the probe barriers at all times during measurement.
Do not measure current in circuits with voltages > 250V
Never perform resistance, diode, transistor or continuity measurements on live
circuits. Make sure all capacitors in the circuit are discharged.
Automatic power-off:
The device will be deactivated automatically when the FUNCTION and RANGE
switch has not been used for 15 minutes. This energy-saving feature extends
the life of your battery.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Perel EVM892 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Perel EVM892 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 0,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info