492085

Perel 4605 Manual

3
Zoom out
Zoom in
Previous page
1/15
Next page
4605-B PEREL
3
1. The single-phase motor is isolated according to class E specifications. The motor frame is made of aluminium or
cast-iron
2. The spark guards are mounted on the steel wheel guards and together they keep sparks from flying everywhere.
3. Grinding wheels
4. Switch
5. The wire has two conductors + ground
6. Capacitor
7. Water trough
8. Gearbox
5. Assembly Instructions
Remove grinder and other parts from box.
Stand grinder on firm, level surface.
Fit eye shield assembly to dry wheel guard using bolt, flat washer and
spring washer.
Fit tool rest to dry wheel guard using flathead bolt, washer and plastic
thumb nut.
6. Operating Instructions
Secure the grinder to a stable and level surface. Positioning the grinder towards the front of the bench will facilitate
the handling of long objects. If possible, leave sufficient room to the left of the device for easy access to the wet
wheel. An alternative method consists in securing the grinder to a sheet of plywood which can then be clamped to a
bench or table to present the grinder in the most convenient position.
Before using the dry wheel make sure that the spark guard is positioned as close to the surface of the wheel as
possible. It's also a good idea to wear safety goggles when operating the grinding machine.
The dry wheel can be used for grinding profiles or bevels on virtually any cutting tool: plane irons, chisels, gouges,
turning tools, drill bits, etc. The aluminium oxide will cut cleanly and without undue heating of the tip of the tool. Take
care, however, not to grind a tool too hard or too long in order to avoid overheating. The final sharpening of the edge
should be carried out on the wet wheel.
Fill the trough with clean water to just below the edge before using the wet wheel. The wet wheel cuts more slowly
than the dry wheel, but the lower speed and the water-cooled operation produce a sharp edge with no risk of burning.
Tools can either be sharpened free-hand or, in the case of those with a long cutting face such as knives, they can be
placed on the notches on the edges of the trough in order to maintain a constant grinding angle.
Note: The EC Declaration of Conformity is attached.
The information in this manual is subject to change without prior notice.
4605-B - TOURET A MEULER MIXTE 200W
1. Introduction et caractéristiques
Aux résidents de l'Union Européenne
Des informations environnementales importantes concernant ce produit
Ce symbole sur l'appareil ou l'emballage indique que, si l'appareil est jeté après sa vie, il peut nuire à
l'environnement.
Ne jetez pas cet appareil (et des piles éventuelles) parmi les déchets ménagers; il doit arriver chez une firme
spécialisée pour recyclage.
Vous êtes tenu à porter cet appareil à votre revendeur ou un point de recyclage local.
Respectez la législation environnementale locale.
Si vous avez des questions, contactez les autorités locales pour élimination.
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Perel 4605 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Perel 4605 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info