525614

Pelgrim GWH 2 Manual

10
Zoom out
Zoom in
Previous page
1/21
Next page
7
lighting
■ Open the gas tap.
■ Turn control knob B to position and
press it in. Gas will now flow to the pilot
light burner.
fig. 8
■ Press ignition button A. A spark will now
jump to the pilot light burner. Keep the
ignition pressed in until the pilot light
ignites, then keep knob B pressed in for
approximately a further 10 seconds.
■ If the pilot light now goes out again, the
preceding action has to be repeated and
ignition button B must be held in for a little
longer.
■ Once the pilot light is lit you can select a
setting between 1 and 7 with thermostat
knob B.
switching off
■ If you turn the control knob to the position
between and 1, only the pilot light will
burn. This is also the frost-protection
position, i.e. at this setting the main burner
will only be switched on at a very low
ambient temperature to keep the room
frost-free. You should therefore leave the
pilot light on during the heating season.
■ Turn control knob B to position . The
heater is now completely switched off.
USE
1
2
3
4
5
6
7
A
B
6
converting to a different type of
gas
■ Check that the values indicated on the
components correspond with the values in
the accompanying table.
■ Close the gas tap.
■ Replace the pressure regulator for natural
gas with the adjusting screw for propane
(or vice versa).
■ Replace the main injection nozzle with the
nozzle from the conversion kit.
■ Replace the pilot light injection nozzle with
the nozzle from the conversion kit.
■ Replace the low-setting restrictor with the
low-setting restrictor from the conversion
kit.
fig. 7
■ Replace the settings plate with the settings
place from the conversion kit.
■ Adjust the burner pressure as per the table
supplied with the conversion kit. In the
case of appliances without pressure
regulator pay particular attention to
whether, with the appliance turned on full,
the supply pressure corresponds with the
appliance’s rated inlet pressure.
■ Check all connections previously
dismantled for leaks.
CONVERSION
9
6
3
1
2
10 11
7
8
5
4
1. Measurement point for burner
pressure
2. Measurement point for supply
pressure
3. Pressure regulator or
adjusting screw
4. Low-setting restrictor
5. Pilot light
6. Mounting bracket
7. Supply pipe
8. Burner pipe
9. Main burner
10. Injection nozzle
11. Taper ring and coupling nut
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pelgrim GWH 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pelgrim GWH 2 in the language / languages: English, Dutch, French as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info