773682
47
Zoom out
Zoom in
Previous page
1/62
Next page
MY20P02-2_1.0_13.01.2020 47
Cleaning and servicing
The rims of a rim brake with invisible wear
indicator are worn as soon as the wear
indicator becomes visible in the area of the rim
joint.
The rims with visible wear indicator are worn as
soon as the black, all-round groove on the pad
friction surface is no longer visible. We
recommend that you also replace the rims with
every second brake lining replacement.
4Check the tension of the spokes.
7.4.1.1 Checking the tyres
Check the tyre wear. The tyre is worn if the
anti-puncture protection or the carcass cords
are visible.
A specialist dealer will need to change the tyre
if it is worn.
7.4.1.2 Checking the rims
Check the rims for wear. The rims are worn as
soon as the black, all-round groove on the pad
friction surface becomes invisible.
Contact your specialist dealer to have the rims
replaced. We recommend that you also replace
the rims at the same time as every second
brake lining replacement.
7.4.1.3 Checking and adjusting the tyre
pressure – Dunlop valve
Only applies to bicycles with this equipment
The tyre pressure cannot be measured on the
simple Dunlop valve. The tyre pressure is
therefore measured in the filling hose when
pumping slowly with the bicycle pump.
It is recommendable to use a bicycle pump with a
pressure gauge. The operating instructions for the
bicycle pump must be adhered to.
1Unscrew and remove the valve cap.
2Connect the bicycle pump.
3Pump up the tyre slowly and pay attention to
the tyre pressure in the process.
4Adjust the tyre pressure according to
specifications in the bicycle pass.
5If the tyre pressure is too high, unfasten the
union nut, let air out and re-tighten the union
nut.
6Remove the bicycle pump.
7Screw the valve cap tight.
8Screw the rim nut gently against the rim with
the tips of your fingers.
7.4.1.4 Checking and adjusting the tyre
pressure – presta valve
Only applies to bicycles with this equipment
It is recommendable to use a bicycle pump with a
pressure gauge. The operating instructions for
the bicycle pump must be adhered to.
1Unscrew and remove the valve cap.
2Open the knurled nut around four turns.
3Carefully apply the bicycle pump so that the
valve insert is not bent.
4Pump up the tyre slowly and pay attention to
the tyre pressure in the process.
5Correct the tyre pressure as per the
specifications on the tyre.
6Remove the bicycle pump.
7Tighten the knurled nut with your fingers.
8Screw the valve cap tight.
9Screw the rim nut gently against the rim with
the tips of your fingers.
7.4.1.5 Checking and adjusting the tyre
pressure – Schrader valve
Only applies to bicycles with this equipment
It is recommendable to use a bicycle pump with a
pressure gauge. The operating instructions for
the bicycle pump must be adhered to.
1Unscrew and remove the valve cap.
2Attach the bicycle pump.
3Pump up the tyre slowly and pay attention to
the tyre pressure in the process.
The tyre pressure has been adjusted as per the
specifications.
4Remove the bicycle pump.
5Screw the valve cap tight.
6Screw the rim nut (1) gently against the rim
with the tips of your fingers.
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pegasus 2020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pegasus 2020 in the language / languages: English as an attachment in your email.

The manual is 7.1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pegasus 2020

Pegasus 2020 User Manual - German - 66 pages

Pegasus 2020 User Manual - Dutch - 63 pages

Pegasus 2020 User Manual - French - 65 pages

Pegasus 2020 User Manual - Italian - 65 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info