769189

Peg Perego Unico Manual

24
Zoom out
Zoom in
Previous page
1/100
Next page
- 24 -
INSTRUCTIONS
UNICO SEAT
1 OPENING: Before opening the Unico Seat, remove
(without using blades) any die-cut cardboard.
Open the seat from the ends, pulling until it clicks.
2 ATTACHING THE SEAT ONTO THE CHASSIS: To fasten the
Unico Seat, position it on the chassis (fig_a) and press
down with both hands until it clicks (fig_b).
Ensure the Unico Seat is properly attached.
3 The Unico Seat can be attached onto the chassis in
“world-facing” (fig_a) or “mum-facing” position (fig_b).
Always engage the brake on the chassis before
fastening and unfastening the seat.
4 REMOVING THE UNICO SEAT FROM THE CHASSIS: To
unfasten the Unico Seat, press the levers near the chassis
attachments (fig_a) and lift the seat at the same time
(fig_b).
5 HOOD: to use the hood, stretch it until it clicks (so it is
completely open).
6 To open the hood, unfasten the Velcro on the rear
(fig_a).
The hood includes a loop to be used to hang your
child's favourite toy (fig_b).
7 Sliding the hood’s attachments on the uprights (fig_a),
you can vary its distance from the seat (fig_b).
8 FRONT BAR: The front bar can be removed by pushing
the buttons on the sides (fig_a), or it can be opened on
one side pressing one button only (fig_b).
9 BED POSITION: the seat can be adjusted in 4 positions,
from “sitting” to “lying”. To switch from one position to
another, pull the lever shown in the picture (fig_a).
ADJUSTING THE BACKREST: press the clip to lower or lift
the backrest to the desired height (Fig. b).
10 COVER (when included): unfasten the Velcro and open
the cover completely (Fig.a). Fit it onto the product,
avoiding the front bar. Fasten both sides on the inside
(Fig.b), then fasten both sides on the outside (Fig. c).
11 COMFORT INSERT: the product comes with a comfort
insert designed to offer additional comfort and support
for baby.
12 5-POINT SAFETY HARNESS: to fasten, insert the two
buckles into the waist strap (with the straps attached
in the crotch strap) until you hear a click (fig_a). To
unfasten them, press the button which is situated at the
centre of the seatbelt buckle and pull the waist strap
outwards (fig_b).
13 To tighten the waist strap, pull on both sides in the
direction of the arrow; to loosen it, do the opposite.
14 The safety harness can be adjusted in 3 positions
according to the child’s height. You must use the higher
positions as the child grows bigger.
15 Adjust the height by sliding the straps through the slots
in the insert and then through those in the backrest
(fig_a) and insert them into the slots required (fig_b).
16 FOLDING THE UNICO SEAT ATTACHED ONTO THE
CHASSIS: the Unico Seat can be folded attached on the
chassis only in world-facing position (fig_a).
To do this:
- the leg rest must be in “sitting” position,
- fold down the hood,
- pull the levers on the up-right (fig_b)
- fold Unico Seat onto itself (fig_c).
17 FOLDING THE CHASSIS WITH THE Unico SEAT FASTENED:
To fold the chassis, we recommend ensuring the front
wheels are fixed and the hood (when fastened) is
closed.
Position the handlebar as shown in the figure (fig_a)
Rotate the safety lever to the left (fig_b) and at the same
time pull the frame’s internal handle towards you (fig_c).
Lift the handle (fig_d) until the frame is completely
folded (fig_e).
18 To fold correctly, check the side fastener is engaged. If
it has not engaged automatically, compress the frame
slightly. The folded stroller is free-standing (fig_a).
TRANSPORT: the stroller can be conveniently carried
(with the front wheels in locked position) using the
central handle (fig_b).
19 WARNING: If Unico Seat is in mum-facing position, it
must be unfastened before folding (fig_a). It can take up
less room when folded (fig_b) .
20 OPENING THE CHASSIS WITH UNICO SEAT ATTACHED:
Press the side attachment fastener downwards, grip
the upper ends of the handle bar and rotate them
towards you until the chassis opens completely (fig_a).
Unico chassis open (fig_b). A “click” sound means it has
opened correctly and corresponds to the attachment
onto the base. Next, open the Unico Seat from the ends,
pulling it until it clicks (fig_c).
21 REMOVING THE LINING: the only element that can be
removed and washed is the comfort insert.
To remove it:
- Release the strap (Arrow 1)
- Remove the buckles from the strap (Arrow 2)
- Slide the straps through the holes (Arrow 3)
- Raise the insert off the seat (Arrow 4).
SERIAL NUMBERS
22 Information about the production date can be found on
the Unico Seat.
_ The product name, production date and serial number
of the chassis.
This information is required for any complaints.
INSTRUCTIONS FOR USE
PRAM BODY
TRANSFORMATION FROM SEAT TO CARRYCOT:
To transform the Unico seat into a carrycot for use from
birth:
- Place the seat in the horizontal position (SEAT - Fig. 9 a).
- Lower the seat’s backrest fully (SEAT - Fig. 9 b).
1 Unfasten the two buckles placed under the seat (Fig. a).
- Press down on the seat to ensure the product opens
completely (Fig. b).
2 Remove the comfort insert from the stroller and slip it
into the sheet provided.
A: INSERT
B: SHEET
Fold the insert’s flaps inwards (arrows 1) and slip the
insert into the sheet (arrows 2).
Insert fitted inside the sheet correctly.
3 Position the Velcro on the cover and close it well (Fig.a).
- Fit the cover onto the carrycot as shown in figure (Fig.b),
avoiding the front bar.
- Button the cover to the carrycot as specified in the
paragraph INSTRUCTIONS FOR USE UNICO SEAT POINT
10 b- c.
4 TRANSFORMATION FROM CARRYCOT TO SEAT:
Fasten the two buckles until they click into place, as
shown in the figure (fig_a). WARNING: slip them through
the slots.
Raise the backrest and place the seat in the desired
position (fig_b).
Pull the comfort insert out of the sheet. Fit the insert
onto the seat.
5 Open the Velcro on the cover, to ensure greater foot
support for baby (fig_c).
Fit the cover onto the seat, avoiding the front bar, and
fasten the 4 side buttons.
6 WARNING: the carrycot must only be used in the
horizontal position (fig_a).
WARNING: from birth up to about 6 months of
age, the stroller should be used in the carrycot
configuration.
WARNING: When the stroller is in the carrycot
configuration, the carrycot should be fastened to
the stroller facing mom (fig_b).
WARNING: do not remove the carrycot from the
stroller while baby is in it.
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Peg Perego Unico at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Peg Perego Unico in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Turkish, Spanish, Finnish as an attachment in your email.

The manual is 4,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info