564332
8
Zoom out
Zoom in
Previous page
1/48
Next page
8
Operating Precautions
Make sure the mains voltage is correct and the same as that printed on the rear of the amplifier. Damage caused by
connecting the amplifier to improper AC voltage is not covered by any CS
®
Series warranty. See the Connecting Power
section for more information on voltage requirements.
Note: Always turn off and disconnect the amplifier from mains voltage before making audio connections. Also, as an
extra precaution, have the attenuators turned down during power-up.
Before powering up, turn the attenuator controls down to prevent speaker damage if there is a high signal level at the
inputs. Always use high-quality input and speaker cables to ensure trouble-free operation. Most intermittent problems
are caused by faulty cables.
Consult the Wire Gauge Charts (page 9) to determine proper gauges for differing load impedances and cable lengths.
Remember that cable resistance robs amplifier power in two ways: power lost directly to resistance (I
2
R loss) and by
lowering the total load impedance. Also make sure the mode switch is correctly set for the desired application. See
sections on Stereo, Parallel and Bridged Mono Operation for more information.
Connecting Inputs
Input connections are made via the three-pin XLR (pin 2+) or 6.3 mm plug combi” connectors on the rear panel of the
amplifier. The inputs are actively balanced and the overload point is high enough to accept the maximum output level
of virtually any signal source.
Connecting Outputs
All models have two output (speaker) connections per channel. Cables can be connected with banana plugs, spade
lugs, or bare wire to the five-way binding posts. The preferred connection method is via the Speakon
®
connectors. Pin
connections are noted on the rear panel.
Connecting Power
CS Series amplifier power requirements are rated at 1/8 power (typical music conditions) and 1/3 power (extreme
music conditions). The maximum power current draw rating is limited only by the front panel circuit breaker. Consult
the specifications in the Appendices section for figures on the current that each amplifier will demand. Unless
otherwise specified when ordered, Peavey amplifiers shipped to customers are configured as follows:
North America - 120VAC/60Hz
Europe, Asia, Australia - 230/240VAC/60-50Hz
South America - 120VAC/60Hz or 240VAC/50Hz
Note: Always turn off and disconnect the amplifier from mains voltage before making audio connections. As an extra
precaution, have the attenuators turned down while powering up.
Introduction
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Peavy CS 1400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Peavy CS 1400 in the language / languages: English as an attachment in your email.

The manual is 3,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info