564332
7
Zoom out
Zoom in
Previous page
1/48
Next page
7
CS
®
1400/2000
Power Amplifiers
Congratulations on your purchase of a Peavey CS Series power amplifier! Designed for years of reliable operation, CS Series
amplifiers offer the sonic superiority and unsurpassed reliability for which Peavey is famous in a rugged, compact unit.
Advanced technologies and extensive protection circuitry allow operation with greater efficiency, even under difficult loads and
power conditions. The exclusive DDT
(Distortion Detection Technique) circuit ensures trouble-free operation into loads as low
as 2 ohms, protects speakers and ensures sonic integrity even in extreme overload conditions. Peavey’s high-efficiency design
uses tunnel-cooled heat sinks and dual-speed DC fans for consistent lower overall operating temperature, resulting in longer
output transistor life.
Peavey CS Series amplifiers are simple to operate and housed in ultra-strong steel chassis, but improper use can be
dangerous. Some CS Series amplifiers are very high powered and can put out high voltages and sizable currents at frequencies
up to 30 kHz. Always use safe operating techniques with these amplifiers.
FOR YOUR SAFETY, READ THE IMPORTANT PRECAUTIONS SECTION, AS WELL AS INPUT, OUTPUT AND POWER
CONNECTION SECTIONS.
Unpacking
Upon unpacking, inspect the amplifier. If you find any damage, notify your supplier immediately. Only the consignee
(the supplier from whom you purchased the amplifier) may institute a claim with the carrier for damage incurred
during shipping. Be sure to save the carton and all packing materials. Should you ever need to ship the unit back to
Peavey or one of its offices, service centers or the supplier, use only the original factory packing. If the shipping carton
is unavailable, contact Peavey to obtain a replacement.
Mounting
CS Series amplifiers will mount in standard 19" racks. Rear mounting ears are also provided for additional support,
which is recommended in non-permanent installations like mobile or touring sound systems. Because of the cables
and connectors on the rear panel, a right angle or offset screwdriver or hex key will make it easier to fasten the rear
mounting ears to the rails.
Cooling Requirements
CS Series amplifiers use a forced-air cooling system to maintain a low, consistent operating temperature. Air is drawn
into the amplifier by fans on the back panel and courses through the cooling fins of the tunnel-configured channel
heat sinks, then exhausts through the front panel grilles. If either heat sink gets too hot, a sensing circuit will mute
the signal for that particular channel. It is important to have an air inlet at the back of the amplifier to allow cooling
air to enter. If the amp is rack mounted, do not use doors or covers on the back of the rack, as the intake air must
flow without resistance. Make sure that there is one (1) standard rack space opening for every three mounted power
amplifiers.
ENGLISH
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Peavy CS 1400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Peavy CS 1400 in the language / languages: English as an attachment in your email.

The manual is 3,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info