564368
25
Zoom out
Zoom in
Previous page
1/32
Next page
Never break off the grounding pin on any equipment. It is provided for your safety. The use of extension
cords should be avoided, but if necessary always use a three-wire type with at least #4 AWG wire size.
Always use a qualied electrician to install any electrical equipment. To prevent the risk of shock or re
hazard, always be sure the amplier and all associated equipment is properly grounded.
NOTE: For UK Only
If the colors of the wires in the mains lead of this unit do not correspond with the colored markings iden-
tifying the terminals in your plug, proceed as follows: (1) The wire that is colored green and yellow must
be connected to the terminal that is marked by the letter E, the Earth symbol, colored green or green and
yellow. (2) The wire that is colored blue must be connected to the terminal that is marked with the letter
N or the color black. (3) The wire that is colored brown must be connected to the terminal that is marked
with the letter L or the color red.

This is the main fuse for the amplier. If this fuse blows, unplug the amplier and switch the POWER and
STANDBY switches off before attempting to replace it. Use only the fuse specied. Care should be taken
when replacing this fuse, as it could be a sign something is seriously wrong with the amplier.

These are the main outputs of the power amplier. These are combination jacks that will accept either
Neutrik® Speakon® connectors OR standard 1/4" inch jacks. Both outputs are in PARALLEL. External
wiring connected to the output jacks should be made by an instructed person or use UL approved, ready-
made leads or cords.

The IMPEDANCE SELECTOR switch is located on the rear of the unit. There are output transformer taps for
2, 4 and 8 ohm loads since these are the most common impedance requirements for bass cabinets. Using
the correct setting is important to ensure longer tube life and maximum performance. It is best if this
switch is congured while the amp is in standby mode. Simply move the selector to the correct impedance
setting.
Tip: If you are unsure about the impedance of your speaker enclosures, just look on the back of your en-
closures. Usually, you will see a 4 ohm or 8 ohm specication. Combining cabinets will change the imped-
ance. If you use two 8 ohm cabinets at the same time (in parallel) you should use the 4 ohm setting, and
if you use two 4 ohm cabinets at the same time (in parallel) you should use the 2 ohm setting.

Seven-pin DIN input for channel switching, compression, graphic EQ and mute with included footswitch.
2
3
4
5
9
8
7
6
5
4
3
10
11
12
13
14
15
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Peavey VB-3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Peavey VB-3 in the language / languages: English as an attachment in your email.

The manual is 4,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info