783293

Peaq PDR360BT Manual

22
Zoom out
Zoom in
Previous page
1/88
Next page
Size = A5
ENGLISH
22
LAN CONFIGURATION
If you do not have a wireless network but do have
a cabled network, you can connect the Internet
radio with a network.
1. Switch the radio o.
2. Connect an Ethernet cable to the LAN socket.
Once switched on and choose wired. The radio
will automatically be recognized as a cable
client.
3. For manual network cable setup go to the
settings (MENU) when using Internet Radio
mode and select System Settings / Internet
Settings / Manual Settings / Cable. Select
DHCP active as the standard setting.
Note
Only use shielded LAN network cable for internet
connection via LAN. If no shielded LAN network
cable is available, please purchase a shielded LAN
network cable for the internet connection via LAN.
WLAN-REGION AND WLAN-NETWORK
Select the WLAN-Region in which you are located.
The device then looks for available wireless
networks. If a wireless network is not found, the
device shows the notifications [Rescan] [Wired]
[Manual config]. Please check in this case
whether your router and WLAN are switched on.
Note
Make sure that the DHCP-server of your router
(Access Point) is activated. Otherwise, the WLAN
connection must be configured manually. The
WLAN should send out the SSID. If the SSID is not
sent out, you must configure the WLAN manually.
•Select the network from which you want to
operate Internet radio.
PUBLIC NETWORK CONNECTION
Select the appropriate WLAN-network by clicking
on the entry of the network’s name. The connection
procedure takes place automatically.
Note
In the Systems settings > Setup wizard, you can
manually configure the network.
PRIVATE NETWORK CONNECTION
Select WPS connection type
If a network is protected by a WEP or WPA
encryption, the query for constructing a connection
over WPS (Wi-Fi Protected Setup) appears. If
the router of your wireless network has a WPS
function, select whether the WPS connection
should be established by entering a PIN code over
the WPS key on the router.
WPS connection using PIN entry
A WPS-PIN appears in the Internet radio display.
Enter this PIN and confirm the Internet radio with
OK. The WPS connection will then be established.
Connection using WPS key
Press the WPS key on the router and then confirm
the display on Internet radio with ENTER. The
WPS connection is then established.
CONNECTION USING THE DIRECT ENTRY OF
THE NETWORK KEY
If you do not want to establish any connection
using the WPS, select the entry, No WPS and then
enter the network key in the following dialogue.
Confirm the entry with ENTER.
COMPLETING THE WLAN CONNECTION
1. The connection begins. The device should
now establish a connection with the WLAN.
Once the connection has been established,
“Connected” appears. Confirm the display with
ENTER.
2. If the WLAN cannot be accessed (e.g. locked
for new WLAN devices) the failure notification
“Connection not successful” appears.
3. In this case, check the setting of your WLAN-
router.
Note
The entered password (WEP / WPA key) will be
saved and will not need to be entered again.
IM_PDR360_180629_A_V04_HR.indb 22 29/6/18 5:27 pm
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Peaq PDR360BT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Peaq PDR360BT in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 12.35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info