558712
7
Zoom out
Zoom in
Previous page
1/12
Next page
9 GB/IE/CY
d)
Look after the device carefully. Check that
moving parts are working properly and
move freely. Check for any parts that are
broken or damaged enough to detrimen-
tally affect the functioning of the device.
Have damaged parts repaired before
you use the device. Many accidents have their
origins in poorly maintained electrical power tools.
e)
Keep cutting tools clean and sharp. Care-
fully maintained cutting tools with sharp cutting edg-
es are less likely to jam and are easier to control.
f) Use the electrical power tool, accesso-
ries, inserted tools etc. in accordance
with these instructions and advice, and
the stipulations drawn up for this
particular type of device. In doing this,
take into account the working condi-
tions and the task in hand. The use of
electrical power tools for purposes other than
those intended can lead to dangerous situations.
Safety advice relating
specifically to random
orbital sanders
J When working in outside areas, protect your-
self against leakage current by fitting an FI pro-
tection switch with a max. activation rating of
30 mA.
J Secure the workpiece firmly. Use clamps or a
vice to firmly hold the workpiece. This results
in a safer grip than with your hand.
J Under no circumstances should you place your
hands next to or in front of the appliance or on
the area to be worked, you could be seriously
injured if you slip or stumble.
J In event of danger, immediately remove the
power plug from the socket.
J Always run the power cable away from the
appliance to the rear.
J FIRE HAZARD DUE TO FLYING SPARKS!
When sanding metals, there is a risk of flying
sparks. For this reason, always make certain
that no one is at risk and that no flammable
materials are located near the working area.
WARNING!
TOXIC VAPOURS!
The working of materials that can produce harm-
ful / toxic dusts presents a health risk for the oper-
ator and for people located in the close vicinity.
Wear safety glasses and a dust
protection mask!
J When working for extended periods on wood
and, in particular, materials that produce dusts
that are hazardous to health, connect the appli-
ance to an appropriate external suction device.
J Provide for sufficient ventilation when working
plastics, varnishes and paints.
J Do not soak materials or surfaces to be worked
with liquids containing solvents. The heat gene-
rated during sanding can give rise to vapours
that are toxic or hazardous to health.
J Avoid sanding lead-based paints or other
materials that are hazardous to health.
J Material containing asbestos may not be worked.
Asbestos is considered to be a carcinogen.
J Avoid contact with the moving sanding sheet.
J Use the appliance only with a sanding sheet in
place.
J Never use the appliance for purposes other
than those intended and only with original
components / accessories.
J Introduce the appliance to the work piece with
it switched on. On task completion, lift the appli-
ance from the work piece and then switch it off.
J Permit the switched off appliance to come to a
complete standstill before putting it down.
J The appliance must always be kept clean, dry
and free of oil or grease.
Q
Original accessories / tools
J Use only the accessories detailed in the operat-
ing instructions. The use of inserted tools or ac-
cessories other than those recommended in the
operating instructions could lead to you suffer-
ing an injury.
General safety advice
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside XQ 600 - KH 3168 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside XQ 600 - KH 3168 in the language / languages: English as an attachment in your email.

The manual is 0,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside XQ 600 - KH 3168

Parkside XQ 600 - KH 3168 User Manual - German, Dutch, French, Italian, Portuguese - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info