Manual Parkside PZKS 1500 A1 - IAN 273098 (page 15 of 64) (English, German, Dutch, French)

706378

Zoom out

Zoom in

1/64

10 GB/IE

• Swing up the machine head (5).

• Undo the screw (e) on the guide bar (37), so that it can

move freely and be pivoted downwards.

• Press the release lever (3). Swing up the saw blade

guard (6) to the point where the recess in the saw

EODGHJXDUGLVDERYHWKHÀDQJHEROW

• Press the saw shaft lock (4) with one hand. With the

RWKHUKDQGLQVHUWWKHDOOHQNH\GLQWKHÀDQJHEROW

• Hold the Allen key (d) and slowly close the saw blade

guard until it touches the Allen key.

• Firmly press the saw shaft lock (4) and slowly rotate the

ÀDQJHEROWLQFORFNZLVHGLUHFWLRQ7KHVDZVKDIWORFN

(4) engages after no more than one rotation.

• 1RZXVLQJDOLWWOHPRUHIRUFHVODFNHQWKHÀDQJHEROW

(31) in the clockwise direction.

• 7XUQWKHÀDQJHVFUHZULJKWRXWDQGUHPRYHWKH

H[WHUQDOÀDQJH

• 7DNHWKHEODGHRIIWKHLQQHUÀDQJHDQGSXOO

out downwards.

• &DUHIXOO\FOHDQWKHÀDQJHVFUHZRXWHUÀDQJH

DQGLQQHUÀDQJH

• Fit and fasten the new saw blade (7) in reverse order.

• Important! The cutting angle of the teeth, in other

words the direction of rotation of the saw blade (7)

must coincide with the direction of the arrow on the

housing.

• Move the guide bar (37) into position and tighten the

screw (e) again.

• Before continuing your work make sure that all safety

devices are in good working condition.

• Important! Every time that you change the saw blade

(7), check to see that it spins freely in the table insert

(11) in both perpendicular and 45° angle settings.

• Important! The work to change and align the saw

blade (7) must be carried out correctly.

8.11 Using the laser (Fig. 3/19/20)

• To switch on: Move the ON/OFF switch of the laser

(34) to the “1” position. A laser line is projected onto

the material you wish to process, providing an exact

guide for the cut.

• To switch off: Move the ON/OFF switch of the laser

(34) to the “0” position.

• Replacing the battery: Switch off the laser (33).

Remove the battery compartment cover (36). Re-

move the batteries and replace with new batteries

(2 x 1.5 Volt Type LR 03 Micro, AAA) Check that

the battery terminals are positioned correctly when

inserting new batteries. Close the battery compart-

ment (35) again.

8.12 Adjusting the laser (Fig. 21)

If the laser (33) ceases to indicate the correct cutting line,

you can readjust the laser. To do so, open the screws

(38) and set the laser by moving sideways to that the

laser beam strikes the teeth of the saw blade (6).

9. Transport

• Tighten the set screw (26) in order to lock the rotary

table (14)

• Activate the release lever (3), press the machine

head (4) downwards and secure with the safety pin

(23). The saw is now locked in its bottom position.

• Fix the saw’s drag function with the locking screw for

drag guide (20) in rear position.

• &DUU\WKHHTXLSPHQWE\WKH¿[HGVDZWDEOH

• When reassembling the equipment proceed as de-

scribed under section 7.1.

10. Maintenance

m Warning! Prior to any adjustment, maintenance or

service work disconnect the mains power plug!

General maintenance measures

Wipe chips and dust off the machine from time to time us-

ing a cloth. In order to extend the service life of the tool, oil

the rotary parts once monthly. Do not oil the motor.

When cleaning the plastic do not use corrosive products.

Brush inspection

&KHFNWKHFDUERQEUXVKHVDIWHUWKH¿UVWRSHUDWLQJ

hours with a new machine, or when new brushes have

EHHQ¿WWHG$IWHUFDUU\LQJRXWWKH¿UVWFKHFNUHSHDWWKH

check every 10 operating hours.

If the carbon is worn to a length of 6 mm, or if the spring

or contact wire are burned or damaged, it is necessary

to replace both brushes. If the brushes are found to be

usable following removal, it is possible to reinstall them.

11. Storage

Store the device and its accessories in a dark, dry and

frost-proof place that is inaccessible to children. The

RSWLPXPVWRUDJHWHPSHUDWXUHLVEHWZHHQDQGÛ&

Store the electrical tool in its original packaging.

Cover the electrical tool in order to protect it from dust

and moisture.

Store the operating manual with the electrical tool.

12. Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies with

the applicable VDE and DIN provisions.

The customer‘s mains connection as well as the

extension cable used must also comply with these

regulations.

• The product meets the requirements of

EN 61000-3-11 and is subject to special connec-

tion conditions. This means that use of the product

at any freely selectable connection point is not al-

lowed.

• Given unfavorable conditions in the power supply the

SURGXFWFDQFDXVHWKHYROWDJHWRÀXFWXDWHWHPSRUDULO\

• The product is exclusively intended for use at con-

nection points that have a continuous current-carry-

ing capacity of at least 100 A per phase.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PZKS 1500 A1 - IAN 273098 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PZKS 1500 A1 - IAN 273098 Manual

Product: