Manual Parkside PZKS 1500 A1 - IAN 273098 (page 13 of 64) (English, German, Dutch, French)

706378

Zoom out

Zoom in

1/64

8GB/IE

• Avoid accidental starting of the machine: the operat-

ing button may not be pressed when inserting the plug

in an outlet.

• Use the tool that is recommended in this manual.

In doing so, your mitre saw provides optimal perfor-

mance.

• Hands may never enter the processing zone when

the machine is in operation. Release the handle but-

ton and switch off the machine prior to any operations.

7. Before starting the equipment

• The equipment must be set up where it can stand

securely. Secure the machine on a workbench or a

VWDQGZLWKVFUHZVWKURXJKWKHKROHVLQWKH¿[HGVDZ

table (15).

• $OOFRYHUVDQGVDIHW\GHYLFHVKDYHWREHSURSHUO\¿WWHG

before the equipment is switched on.

• It must be possible for the blade to run freely.

• When working with wood that has been processed

before, watch out for foreign bodies such as nails or

screws, etc.

• Before you press the ON/OFF switch check that the saw

EODGHLV¿WWHGFRUUHFWO\0RYLQJSDUWVPXVWUXQVPRRWKO\

• Before you connect the equipment to the power sup-

ply make sure the data on the rating plate are dentical

to the mains data.

8. Attachment and operation

8.1 Attaching the saw (Fig1/2/3/4/5)

• In order to adjust the rotary table (14) loosen the set

screw (26) approx. 2 turns.

• Turn the rotary table (14) and pointer (12) to the de-

sired angle measurement on the scale (13) and secure

with the set screw (26).

• Pressing the machine head (4) lightly downwards and

removing the locking bolt (23) from the motor bracket

at the same time disengages the saw from the low-

est position.

• Swing the machine head (4) up until the release lever

(3) latches into place.

• It is possible to secure the clamping device (7) to the

left or right on the stationary saw bench (15). Insert the

clamping device (7) in the hole on the rear side of the

stop rail (16) and secure it with the star grip screw (7a).

• $WWDFK WKH ZRUNSLHFH VXSSRUWV  WR WKH ¿[HG VDZ

table (15) as shown in Figure 5 and fasten with the

screw (9).

• It is possible to tilt the machine head (4) a max. 45° to

the left by loosening the set screw (22).

8.2 Precision adjustment of the stop for crosscut

90° (Fig. 1/6/7)

• No stop angle included.

• Lower the machine head (4) and secure using the

locking bolt (23).

• Loosen the set screw (22).

• Position the angle stop (a) between the saw blade

(6) and the rotary table (14).

• Adjust the adjusting screw (27) until the angle be-

tween the saw blade (6) and rotary table (14) is 90°.

• ,WLVQRWQHFHVVDU\WR¿[WKLVVHWWLQJEHFDXVHLWLV

maintained by the spring pretension.

• Subsequently check the position of the angle indi-

cator. If necessary loosen the pointer (19) using a

Philips screwdriver, set to position 0° on the angle

scale (18) and re-tighten the retaining screw.

8.3 Cross cut 90° and turntable 0° (Fig.8)

In the case of cutting widths up to approx. 100 mm it

LVSRVVLEOHWR¿[WKHWUDFWLRQIXQFWLRQRIWKHVDZZLWK

the set screw (20) in the rear position. In this position

the machine can be operated in cross cutting mode. If

the cutting width is over 100 mm then it is necessary

to ensure that the set screw (20) is loose and the ma-

chine head (4) can move.

Attention! For 90° cross cuts, the moveable stop rail

DPXVWEH¿[HGLQWKHLQQHUSRVLWLRQ

• Open the set screw (16b) on the moveable stop rail

(16a) and push the moveable stop rail (28) inwards.

• The moveable stop rail (16a) must be locked in a

position far enough from the inner position that the

distance between the stop rail (16a) and the saw

blade (6) is no more than 8 mm.

• Before making the cut, check that no collision could oc-

cur between the stop rail (16a) and the saw blade (6).

• Tighten the set screw (16b) again.

• Move the machine head (4) to its upper position.

• Use the handle (3) to push back the machine head

DQG¿[LWLQWKLVSRVLWLRQLIUHTXLUHGGHSHQGHQW

on the cutting width).

• Place the piece of wood to be cut at the stop rail

(16) and on the turntable (14).

• Lock the material with the clamping device (7) on

WKH¿[HGVDZWDEOHWRSUHYHQWWKHPDWHULDOIURP

moving during the cutting operation.

• Push down the release lever (3) to release the ma-

chine head (4).

• Press the ON/OFF switch (2) to start the motor.

• :LWKWKHGUDJJXLGH¿[HGLQSODFH

use the handle (1) to move the machine head (4) steadi-

ly and with light pressure downwards until the saw blade

(6) has completely cut through the work piece.

• :LWKWKHGUDJJXLGHQRW¿[HGLQSODFH

• pull the machine head (4) all the way to the front.

Lower the handle (1) to the very bottom by apply-

ing steady and light downward pressure. Now push

the machine head (4) slowly and steadily to the

very back until the saw blade (6) has completely cut

through the work piece.

• When the cutting operation is completed, move the

machine head (4) back to its upper (home) position

and release the ON/OFF button (2).

Attention! The machine executes an upward stroke

automatically due to the return spring, i.e. do not re-

lease the handle (1) after completing the cut; instead

allow the machine head to move upwards slowly

whilst applying light counter pressure.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PZKS 1500 A1 - IAN 273098 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PZKS 1500 A1 - IAN 273098 Manual

Product: