Manual Parkside PSZ 250 B2 - IAN 100684 (page 9 of 53) (English, German, Dutch, Polish)

595354

Zoom out

Zoom in

1/53

9 GB

ATTENTION! In the event of an emergency, imme-

diately activate the emergency stop switch

to stop

the cable hoist. The cable hoist cannot be operated

if the emergency stop switch has been activated.

Cleaning, maintenance and

ordering spare parts

Cleaning

ATTENTION! Unplug the mains plug from the

socket before cleaning.

Do not use cleaners or solvents; these could

aﬀect the plastic parts of the device.

Ensure water cannot penetrate the housing.

Keep safety devices, venting slots and the motor

housing as dust and dirt free as possible.

Rub the device down with a clean cloth or

blow out with compressed air at a low pressure

setting.

Regularly clean the device with a damp cloth and

a little soft soap.

Note: We recommend cleaning the device

immediately after every use.

Maintenance

ATTENTION! Verify the device is not connected to

the mains when performing care.

Below: A cycle corresponds to moving a load up

and down once.

Periodic inspection corresponds to an inspection

after 100 cycles.

Periodically check the end switches on the cable

hoist are working properly (check without load).

Test as follows: When the cable reaches the

maximum hoisting height the auto-stop mecha-

nism lever

is activated. The motor

must

now stop. When the steel cable

is unwound

as far as possible, the maximum cable length

lever

is activated. The motor

must now

stop.

Periodically check the power cable

and the

control lead

Lubricate the steel cable

and pulley

every

200 cycles.

Every 30 cycles verify the entire steel cable

is in good working order in accordance with Fi-

gure I. If damaged, it must be replaced with a

steel cable corresponding with the technical data.

Every 1000 cycles check the screws on the

mounting bracket

and pulley

are tight.

Every 1000 cycles verify the hooks

and the pulley

are in good condition.

Verify the emergency stop switch

and push

buttons

are in good condition before every

use.

Check the brake system every 1000 cycles. If

the motor

emits unusual noises or is unable

to hoist the rated load, the brake system may

need to be overhauled:

- Replace damaged or worn parts and keep

the associated maintenance documentation.

- Please contact an authorised service centre

for unscheduled maintenance work.

Disposal

The device is packaged to protect it from transport

damage. This packaging is a raw material and there-

fore reusable or may be recycled. The device and

its accessories are made from various materials, e.g.

metal and plastics.

Dispose of defective components through toxic waste

disposal. Contact the speciality retailer or your mu-

nicipal government for information!

Do not dispose of power

tools in household waste!

In accordance with European Directive 2012 / 19 /

on waste electrical and electronic equipment and

its implementation into national legislation, worn

out power tools must be collected separately and

recycled in an environmentally friendly fashion.

Operation / Cleaning, maintenance and ordering spare parts / Disposal

Safety notices specific to the device / Before using / Operation

100684_par_Seilhebelzug_content_PL_SI_SK_NL.indd 9 02.07.14 12:41

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PSZ 250 B2 - IAN 100684 in the language / languages: English, German, Dutch, Polish as an attachment in your email.

The manual is 6,15 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PSZ 250 B2 - IAN 100684 Manual

Product: