763012

Parkside PSKO 24 A1 - IAN 354867 Manual

21
Zoom out
Zoom in
Previous page
1/32
Next page
17GB
7. Technical data
Mains connection ................................................ 230 V∼ 50 Hz
Motor power ..................................................................1500 W
Operating mode .......................................................................S1
Compressor speed .....................................................2800 min-1
Pressure vessel capacity ..........................................approx. 24 l
Operating pressure ...............................................approx. 8 bar
Theo. intake capacity ....................................approx. 260 l/min
Effective delivery quantity at 7 bar .................approx. 80 l/min
Effective delivery quantity at 4 bar .............. approx. 110 l/min
Effective delivery quantity at 1 bar .............. approx. 150 l/min
Sound pressure level LPA ............................................... 68 dB(A)
Sound power level LWA ..................................................89 dB(A)
Uncertainty KPA/WA ..........................................................2.59 dB
Protection category ...............................................................IP20
Device weight ....................................................... approx. 24 kg
Max. altitude (above mean sea level) ...........................1000 m
The noise emission values have been determined in accordance
with EN ISO 3744:1995.
Wear hearing protection.
Excessive noise can result in a loss of hearing.
8. Before commissioning
• Open the packaging and carefully remove the device.
• Remove the packaging material, packaging and transport
safety devices (if applicable).
• Check that the delivery is complete.
• Check the device and accessory parts for transport damage.
• If possible, keep the packaging until the end of the warranty
period.
DANGER
The device and the packaging are not children‘s
toys! Do not let children play with plastic bags,
films or small parts! There is a danger of choking
or suffocating!
• Before connecting the machine, make certain that the data
on the type plate matches with the mains power data.
• Check the device for transport damage. Report any damage
immediately to the transport company which was used to
deliver the compressor.
• Install the compressor near the point of consumption.
• Avoid long air lines and supply lines (extension cables).
• Make sure that the intake air is dry and free of dust.
• Do not install the compressor in a damp or wet room.
• The compressor may only be used in suitable rooms (with
good ventilation and an ambient temperature from +5 °C
to 40 °C). There must be no dust, acids, vapours, explosive
gases or inflammable gases in the room.
• The compressor is designed to be used in dry rooms. It is
prohibited to use the compressor in areas where work is
conducted with sprayed water.
• The compressor may only be used outdoor briefly when the
ambient conditions are dry.
• The compressor must always be kept dry and must not be left
outdoors after work is complete.
9. Attachment and operation
m Attention!
Always make sure the device is fully assembled
before commissioning!
You require the following for assembly:
1x open-ended spanner 14 mm
1x Phillips screwdriver
(not included in the scope of delivery)
9.1 Fitting the wheels (fig. 3)
• Fit the supplied wheels (5) as shown.
9.2 Installing the supporting foot (fig. 4)
• Fit the supplied supporting foot (7) as shown.
9.3 Installing the air filter (fig. 5, 6)
• Remove the transport lid (16) and screw the air filter (4) to
the equipment.
• Insert the hose (4d) into the opening of the air filter (4).
9.4 Mains connection
• The compressor is equipped with a mains cable with
protective contact plug. This can be connected to any 220 ‒
240 V∼ 50 Hz protective contact socket, with fuse protection
of at least 16A.
• Before you use the machine, make sure that the mains voltage
is the same as the operating voltage and the machine power
on the rating plate.
• Long supply cables, extensions, cable reels, etc. cause a
drop in voltage and can impede motor start-up.
• At low temperatures below +5 °C, sluggishness may make
starting difficult or impossible.
9.5 On/Off switch (fig. 1)
• Pull the On/Off switch (3) upwards to switch on the
compressor.
• To switch off the compressor, press the On/off switch (3)
down.
9.6 Setting the pressure (fig. 1, 2)
• Use the pressure regulator (15) to set the pressure on the
pressure gauge (12).
• The pressure set can be drawn from the quick couplings (10,
11).
• The vessel pressure can be read off at the pressure gauge (13).
9.7 Setting the pressure switch (fig. 1)
• The pressure switch (2) is set at the factory.
Cut-in pressure approx. 5.5 bar
Cut-out pressure approx. 8 bar
9.8 Fitting the compressed air hose (fig. 1, 2)
• Connect the plug nipple (14a) of the compressed air hose
(14) to one of the quick couplings (10, 11). Then attach
the compressed air tool to the quick coupling (14b) of the
compressed air hose (14).
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PSKO 24 A1 - IAN 354867 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PSKO 24 A1 - IAN 354867 in the language / languages: English, German as an attachment in your email.

The manual is 3,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info