796059

Parkside PPFSA 40-Li A1 - IAN 376667 Manual

44
Zoom out
Zoom in
Previous page
1/236
Next page
44
GB IE
Dismantling:
1. Release the shaft tube mounting screw
(23).
2. Push the lock (24).
3. Pull apart the shaft tubes (3 + 6).
Mounting the protective
cover
Never use the device without
the protective cover properly
mounted. There is a risk of injury.
1. Position the protective cover (7) on the
shaft mount (27).
2. Attach the protective cover (7) using
the multi-function key (18) and the two
small screws (25).
Mounting the handles
1. Loosen the star screw (30) and remove
the handle mount (29) from the upper
shaft tube (3).
2. Place the multifunction handle (8) and
handle (5) into the receptor (28) on the
upper shaft tube (3).
3. Fasten the handles (5 + 8) to the han-
dle mount (29) and star screw (30).
Tighten the star screw (30) by hand.
4. Fasten the device cable to the cable
holders (4).
Mounting/replacing the
spool
1. Switch off the motor and remove the
battery from the device.
2. Place the device on the ground in a
stable position.
3. Block the uptake spindle (31) using the
Allen key (17) as depicted.
Screw the spool cap (15) clockwise
from the uptake spindle (31).
4. Open the spool cap (15) by  rmly
pressing the quick-release catch (38)
inwards on both sides of the spool cap
(15), and remove the spool cap cover.
5. Insert the two ends of the line of the
new spool (33) through the line outlet
loop (32).
6. Place the spool (33) into the spool cap
(15) and allow the cover to latch back
into the spool cap (15).
7. Screw the spool cap (15) anticlockwise
back onto the uptake spindle (31).
Remove the Allen key (17).
8. Pull on both ends of the line to release
the lines from the grooves.
9. Trim the thread line to approx. 15 cm
to release strain on the engine when
starting and warming up.
The washer (35), clamping disk
(36) and nut (37) are not required
for mounting the spool.
Mounting/replacing the
blade
Risk of injury! Caution -
sharp edges!
Wear gloves.
1. Switch off the motor and remove the
battery from the device.
2. Place the device on the ground in a
stable position.
3. Place the 2-tooth blade (16) onto the
uptake spindle (31). The blade can be
used on both sides.
4. Fasten the blade using the multifunction
key (18) and the washer (35), clamp-
ing disk (36) and nut (37).
5. Remove the Allen key (17).
… 44 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PPFSA 40-Li A1 - IAN 376667 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PPFSA 40-Li A1 - IAN 376667 in the language / languages: English, German, Dutch, Danish, French, Polish, Spanish as an attachment in your email.

The manual is 3.76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info