779757
32
Zoom out
Zoom in
Previous page
1/148
Next page
32
GB IE
3. Release the spindle locking button (10).
4. Take out the 8 mm collet chuck (12)
using pliers and insert the 6 mm collet
chuck (20) that is included in the deli-
very. You will hear it click into place.
5. Screw the cap nut (11) loosely back
on.
Tighten the cap nut only when a
cutter is inserted. The collet chuck
might get damaged.
Mounting the suction
adapter
You can reduce dust formation while you
work by connecting a dust suction system.
1. Unlock the cutting depth rough adjust-
ment by turning the locking knob (16)
anticlockwise about half way.
2. Press and hold the cutting depth rough
adjustment button (6).
3. Now move the drive unit (5) fully up
to the top. The drive unit (5) and ba-
seplate (9) are now at the maximum
distance from one another.
4. Let go of the button (6).
5.
Fit the suction adapter (21) into the reces-
ses provided (13) in the baseplate (9).
6. To lock, turn the suction adapter (21)
clockwise as far as it allows.
4. Connect the suction hose of a vacuum
cleaner to the suction adaptor (21).
The vacuum cleaner must be
suitable for the workpiece to be
processed. Use a special vacuum
cleaner if dusts with hazard for
health are created.
Inserting/changing
cutters
To insert and replace cutters, wear
protective gloves to prevent cuts
and burns.
1. Press the spindle locking button (10)
on the side of the device and keep it
pressed down.
2. Use the combination wrench (19) to
loosen the cap nut (11) as much as nee-
ded, so that the cutter can be inserted.
3. Release the spindle locking button (10).
4. Insert the desired cutter into the already
mounted collet chuck (12). The cutter
shaft must be pushed in at least 20 mm.
5. Use the combination wrench (19) to
tighten the cap nut (11) while kee-
ping the spindle locking button (10)
pressed.
Tighten the cap nut only when a
cutter is inserted. The collet chuck
might get damaged.
Mounting the parallel stop
1. Unscrew both retaining screws (15) on
the top side of the baseplate.
2. Now insert the parallel stop (22) into
the receptor (14) provided on the base-
plate (9).
3. Fix the parallel stop into the desired
position using the retaining screws (15).
Adjust cutting depth
The cutting depth may only
be set when the device is
switched off
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside POFA 12 A1 - IAN 308577 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside POFA 12 A1 - IAN 308577 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 3.59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info