Manual Parkside PMTS 210 A1 - IAN 367465 (page 10 of 152) (English, German, Dutch, Danish, French, Polish, Spanish)

779278

Zoom out

Zoom in

1/152

4GB/IE

4. Scope of delivery

• Saw blade guard (4)

• Push stick (14)

• Parallel stop (7)

• Transverse stop (2)

• Table width extension (22)

• End piece of table width extension (24) 2x

• Screw for end piece of table width extension (25)

2x M3x8 self-tapping

• Ring spanner 19/10 mm (21)

• Ring spanner 7/8 mm (20)

• Bracket for workbench mounting (42) 2x

• Screw M3x8 self-tapping (43) 2x

• Washers d 4mm (44) 2x

• Wooden screw for workbench mounting (45) 2x

• Operating manual

5. Proper use

The circular table saw is used for the longitudinal and trans-

verse cutting (only with the transverse stop) of all types of tim-

bers and plastic, in accordance with the machine size. It is not

permitted to cut any type of round timber.

The machine may only be used in the intended manner. Any

use beyond this is improper. The user/operator, not the manu-

facturer, is responsible for damages or injuries of any type re-

sulting from this.

Only suitable saw blades (HM or CV saw blades) may be

used for the machine. The use of HSS saw blades and any type

of cutting wheels is prohibited.

An element of the proper intended use is also the observance

of the safety instructions, as well as the assembly instructions

and operating information in the operating manual.

Persons who operate and maintain the machine must be fa-

miliar with the manual and must be informed about potential

dangers. In addition, the applicable accident prevention regu-

lations must be strictly observed.

Other general occupational health and safety-related rules and

regulations must be observed.

m ATTENTION

When using equipment, several safety warnings must be ob-

served to prevent injuries and damage. For this reason, please

carefully read this operating manual / safety instructions. Keep

them in a safe place so that the information is available at all

times. If you hand the device over to another person, please

hand over this operating manual / safety instructions as well.

We accept no liability for accidents or damage that occur due

to a failure to observe this manual and the safety instructions.

The liability of the manufacturer and resulting damages are ex-

cluded in the event of modiﬁcations of the machine.

Despite use as intended, speciﬁc risk factors cannot be entirely

eliminated. Due to the design and layout of the machine, the

following risks remain:

• Contact with the saw blade in the exposed sawing area.

• Reaching into the running saw blade (cutting injury)

• Kick-back of workpieces and workpiece parts

• Saw blade breakage

• Ejection of faulty carbide parts of the saw blade

• Hearing damage when the necessary hearing protection is

not used.

• Harmful emissions of wood dusts during use in enclosed areas.

Please note that our equipment was not designed with the inten-

tion of use for commercial or industrial purposes. We assume

no guarantee if the device is used in commercial or industrial

applications, or for equivalent work.

6. Safety instructions

General power tool safety warnings

m WARNING: Read all safety warnings, instruc-

tions, illustrations and speciﬁcations provided with

this power tool.

Failure to follow all instructions listed below may result in elec-

tric shock, ﬁre and/or serious injury.

Save all warnings and instructions for future refer-

ence.

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

power tool.

1) Work area safety

a) Keep your work area clean and well-lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmos-

pheres, such as in the presence of ﬂammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

c) Keep children and bystanders away while op-

erating a power tool. Distractions can cause you to

lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁed plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed surfaces, such

as pipes, heaters, ovens and refrigerators. There

is an increased risk of electric shock if your body is earthed

or grounded.

c) Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase the risk

of electric shock.

d) Do not abuse the cord. Never use the cord for car-

rying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of elec-

tric shock.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PMTS 210 A1 - IAN 367465 in the language / languages: English, German, Dutch, Danish, French, Polish, Spanish as an attachment in your email.

The manual is 3.98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PMTS 210 A1 - IAN 367465 Manual

Product: