Manual Parkside PMTS 210 A1 - IAN 367465 (page 9 of 152) (English, German, Dutch, Danish, French, Polish, Spanish)

779278

Zoom out

Zoom in

1/152

3GB/IE

2. Introduction

Manufacturer:

scheppach

Fabrikation von Holzbearbeitungsmaschinen GmbH

Günzburger Straße 69

D-89335 Ichenhausen

Dear Customer,

We hope your new tool brings you much enjoyment and suc-

cess.

Note:

In accordance with the applicable product liability laws, the

manufacturer of this device assumes no liability for damage to

the device or caused by the device arising from:

• Improper handling

• Failure to comply with the operating manual,

• Repairs carried out by third parties, unauthorised specialists.

• Installing and replacing non-original spare parts,

• Improper use

• Failures of the electrical system in the event of the electri-

cal regulations and VDE provisions 0100, DIN 57113 /

VDE0113 not being observed.

Note:

Read the whole text of the operating manual before assembly

and commissioning.

This operating manual should help you to familiarise yourself

with your device and to use it for its intended purpose.

The operating manual includes important instructions for safe,

proper and economic operation of the device, for avoiding

danger, for minimising repair costs and downtimes, and for

increasing the reliability and extending the service life of the

device.

In addition to the safety instructions in this operating manual,

you must also observe the regulations applicable to the opera-

tion of the device in your country.

Keep the operating manual at the device, in a plastic sleeve,

protected from dirt and moisture. They must be read and care-

fully observed by all operating personnel before starting the

work.

The device may only be used by personnel who have been

trained to use it and who have been instructed with respect to

the associated hazards. The required minimum age must be

observed.

In addition to the safety instructions in this operating manual

and the separate regulations of your country, the generally

recognised technical rules relating to the operation of such ma-

chines must also be observed.

We accept no liability for accidents or damage that occur due

to a failure to observe this manual and the safety instructions.

3. Device description (ﬁg. 1-26)

1. Saw table

2. Transverse stop

3. Riving knife

4. Saw blade guard

4a. Wing nut with washer (saw blade guard)

4b. Carriage bolt (saw blade guard)

4c. Extraction port (saw blade guard)

5. Saw blade

6. Table inlay

7. Parallel stop, complete

8. Handwheel (cutting depth adjustment)

8a. Handwheel (cutting angle adjustment)

9. Locking screw (cutting angle adjustment)

10. Overload switch

11. On/oﬀ switch

12. Rubber foot (4x)

13. Tool hook

14. Push stick

15. Locking screw (parallel stop) (2x)

15a. Clamping plate (parallel stop) (2x)

16. Holder (parallel stop)

16a. Screw (parallel stop)

17. Stop rail (for parallel stop or transverse stop)

18. Knurled screw (transverse stop)

19. Turning handle (parallel stop)

20. Ring spanner 7/8mm

21. Ring spanner, 19/10mm

22. Table width extension

23. Guide tube (table width extension)

24. End piece (table width extension) (2x)

25. Screw (for end piece of table width extension;

2x M3x8 self-tapping)

26. Knurled screw (table width extension)

27. Guide bushing (table width extension)

28. Height adjustment screw (table width extension)

29. Counternut (height adjustment screw)

30. Support foot (table width extension)

31. Hole (riving knife)

32. Screw (table inlay)

33. Fixing screw (riving knife)

34. Screw (saw blade cover)

35. Saw blade cover

36. Extraction port

37. Groove (stop rail for thick material)

38. Scale

39. Groove (stop rail for thin material)

40. Groove (saw table)

41. Mains cable

42. Bracket for workbench mounting (2x)

43. Screw (2x; M3x8 self-tapping)

44. Washers (2x; d 4mm)

45. Wood screw (for workbench mounting)

46. Holder (parallel stop)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PMTS 210 A1 - IAN 367465 in the language / languages: English, German, Dutch, Danish, French, Polish, Spanish as an attachment in your email.

The manual is 3.98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PMTS 210 A1 - IAN 367465 Manual

Product: