Manual Parkside PMPS 200 A1 - IAN 389215 (page 23 of 365) (English, German, Dutch, Danish, French, Italian, Polish, Spanish)

796098

Zoom out

Zoom in

1/365

GB/IE/NI/CY/MT 23

For reduced spatter and a more stable arc, you can select the Pulse MIG method. With this method you

can choose between steel wire, CrNi, CuSi, AlMg, AlSi and Al wire [drawing 5]. In addition, the inert

gas required will be speciﬁed.

When using particular wires, use the following inert gases:

Fe (steel wire): [80% Argon/20% CO2]

CrNi (stainless steel) wire: [98% Argon/2% CO2]

CuSi, AlMg, AlSi and aluminium wire: [100% Argon]

Navigation within the PMIG menu is carried out in a similar way to navigation in the “MAG” menu

using the switches 12 and 13. The diameter of the welding wire used can also be set and you can select

“2T” and “4T”.

zDPMIG welding

Using the double pulse MIG method, less heat is transferred into the material. Because of this,

thismethod is particularly suitable for welding thin sheets of stainless steel and aluminium.

With this method the same wire electrodes and inert gases can be used as with PMIG welding.

Navigation within the DPMIG menu is carried out in a similar way to navigation in the “MAG” menu

using the switches 12 and 13. The diameter of the welding wire used can also be set and you can select

“2T” and “4T”.

In addition, after setting the welding wire used, this is where you can recall the parameter diagram by

pressing the switch 13 twice. This is where you can set the individual parameters for the DPMIG method.

We recommend that you use the pre-set values at this point. As an advanced user, you can adjust the

individual values to adapt the welding procedure precisely to your planned work. To reset the parame-

ters which have been set, return to the DPMIG [drawing 6] and keep the switch 12 pressed for approx.

5 seconds.

Drawing 6

RISK OF BURNS!

Welded workpieces are very hot and can cause burns. Always use pliers to move hot, welded

workpieces.

Please proceed as follows once you have electrically connected the

welder:

 Put on appropriate protective clothing in accordance with the speciﬁcations and prepare your

workplace.

 Connect the earthing cable to 4 the workpiece that is to be welded using the earth terminal.

Please ensure good electrical conductivity.

 The area to be welded on the workpiece must be free of rust and paint.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PMPS 200 A1 - IAN 389215 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 6.17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PMPS 200 A1 - IAN 389215 Manual

Product: