634195

Parkside PMFW 280 A2 - IAN 93266 Multi-Purpose Tool Manual

9
Zoom out
Zoom in
Previous page
1/60
Next page
9 GB/IE
General safety advice for electrical power tools General safety advice for electrical power tools / Assembly
Safety advice relating specifi-
cally to this multifunction tool
When working, hold the electrical
power tool firmly with both hands and
keep a proper footing and balance. It
is safer to guide the electrical power tool using
both hands.
Secure the workpiece. A workpiece held
in a clamp or vice is kept more securely in
place than one held by your hand.
Keep your working area clean. Mixtures
of materials can be particularly dangerous.
Light metal alloy dust may burn or explode.
Do not operate the device if the mains
lead or mains plug is damaged.
Do not touch the mains lead if it be-
comes damaged or cut through while
you are using the device. Pull the plug
out of the mains socket immediately and have
the device repaired by a suitably qualified per-
son or at your service centre. Damaged mains
leads increase the risk of electric shock.
Wear protective gloves when replacing
a tool in the device. Tools heat up with
prolonged use.
Use the electrical power tool only for
dry abrading / sawing / cutting.
Do not operate the device if it is damp
and do not use it in a damp environ-
ment. Water entering an electrical device in-
creases the risk of electric shock.
Keep your hands away from the area
of the saw blade. Do not grip the underside
of the workpiece. Contact with the saw blade
may result in injury.
Use a suitable detector to locate con-
cealed services supply cables / pipes
or approach your local public utilities
services providers. Contact with electricity
cables can lead to fire or electric shock.
Damaging a gas pipe can lead to an explo-
sion. Penetration of a water pipe can lead to
property damage or to electric shock.
If you use the device outdoors, always
connect it through a residual current
device (RCD) with a maximum trip cur-
rent of 30 mA. If using an extension lead, al-
ways use one that is approved for outdoor use.
Any harmful / noxious dusts
generated from sanding represent a risk to the
health of the person operating the device and
to anyone near the work area.
Wear safety glasses and a dust pro-
tection mask!
Ensure that there is adequate ventila-
tion when working on plastic, paint,
varnish etc.
Do not soak the materials or the sur-
face you are about to work on with
liquids containing solvents.
Q
Advice on use
Principle of operation:
The oscillating drive causes the attached tool to vi-
brate backwards and forwards up to 21000 times
per minute. This means the tool can produce precise
work in the tightest of spaces.
Sawing / cutting:
Use only undamaged, defect-free saw blades.
Distorted, blunt or otherwise damaged saw
blades could break.
When sawing lightweight building materials,
observe the statutory requirements and the
manufacturer’s recommendations.
Use the device in plunge sawing mode on soft
materials such as wood, gypsum plaster board
etc. only!
Sanding:
Ensure that you use even contact pressure. This
will increase sanding sheet life.
Q
Assembly
Q
Vacuum extraction of
dust / debris
Do not use the tool on materials containing asbestos.
Asbestos is a known carcinogen.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PMFW 280 A2 - IAN 93266 Multi-Purpose Tool at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PMFW 280 A2 - IAN 93266 Multi-Purpose Tool in the language / languages: French, Swedish as an attachment in your email.

The manual is 2,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PMFW 280 A2 - IAN 93266 Multi-Purpose Tool

Parkside PMFW 280 A2 - IAN 93266 Multi-Purpose Tool User Manual - English, German, Dutch - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info