706392

Parkside PKS 1700 B2 - IAN 79729 Manual

51
Zoom out
Zoom in
Previous page
1/58
Next page
GB
- 51 -
more than one rotation.
•
Now, using a little more force, slacken the
flange bolt (31) in the clockwise direction.
•
Turn the flange screw (31) right out and remo-
ve the external flange (32).
•
Take the blade (7) off the inner flange (38)
and pull out downwards.
•
Carefully clean the flange screw (31), outer
flange (32) and inner flange (38).
•
Fit and fasten the new saw blade (7) in rever-
se order.
•
Important! The cutting angle of the teeth,
in other words the direction of rotation of the
saw blade (7) must coincide with the direction
of the arrow on the housing.
•
Before continuing your work make sure that
all safety devices are in good working condi-
tion.
•
Important! Every time that you change the
saw blade (7), check to see that it spins freely
in the table insert (11) in both perpendicular
and 45° angle settings.
•
Important! The work to change and align
the saw blade (7) must be carried out correct-
ly.
7.8 Transport (Fig. 1-3)
•
Retighten the locking grip (13) to secure the
turntable (16) in place.
•
Activate the release lever (3), press the ma-
chine head (5) downwards and secure with
the safety pin (25). The saw is now locked in
its bottom position.
•
Fix the saw’s drag function with the locking
screw for drag guide (24) in rear position.
•
Carry the equipment by the fixed saw table
(17).
•
When reassembling the equipment proceed
as described under section 6.2.
7.9 Using the laser (Fig. 21-23/Item 33)
•
To switch on: Move the ON/OFF switch
of the laser (34) to the “1” position. A laser
line is projected onto the material you wish to
process, providing an exact guide for the cut.
•
To switch off: Move the ON/OFF switch of
the laser (34) to the “0” position.
•
Setting the laser: The laser is adjusted with
the screw (37) and glued in place ex-works.
Further adjustment of the laser during operati-
on is not required. Important. Do not look into
the laser beam.
•
Replacing the battery: Switch off the
laser (33). Remove the battery compartment
cover (36). Remove the batteries and replace
with new batteries (2 x 1.5 Volt Type R03, LR
03 Micro, AAA) Check that the battery termi-
nals are positioned correctly when inserting
new batteries. Close the battery compartment
(35) again.
8. Replacing the power cable
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel to
avoid danger.
9. Cleaning, maintenance and
ordering of spare parts
Always pull out the mains power plug before star-
ting any cleaning work.
9.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use cleaning
agents or solvents; these could attack the
plastic parts of the equipment. Ensure that no
water can seep into the device.
Anl_4300685.indb 51Anl_4300685.indb 51 08.10.12 17:2308.10.12 17:23
… 51 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PKS 1700 B2 - IAN 79729 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PKS 1700 B2 - IAN 79729 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 3,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PKS 1700 B2 - IAN 79729

Parkside PKS 1700 B2 - IAN 79729 User Manual - French, Italian - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info