706392

Parkside PKS 1700 B2 - IAN 79729 Manual

50
Zoom out
Zoom in
Previous page
1/58
Next page
GB
- 50 -
button (2).
7.2 Cross cut 90° and turntable 0° - 45°
(Fig. 1-3, 13)
The crosscut saw can be used to make crosscuts
of 0° -45° to the left and 0° -45° to the right in
relation to the stop rail.
•
Release the turntable (16) by slackening the
locking grip (13).
•
Press the latched position lever (12). Turn the
turntable (16) and scale pointer (14) to the
desired angular setting on the scales (15) and
lock into place with the locking grip (13). The
saw has locking positions at angles of - 45°,
-30°, -22.5°, -15°, 0°, 15°, 22.5°, 30°
and 45°, at which you can engage latched
position lever (12).
•
Cut as described under section 7.1.
7.3 Miter cut 0°- 45° and turntable 0°
(Fig. 1-3, 14)
The crosscut saw can be used to make miter cuts
of 0° - 45° in relation to the work face.
•
If required, dismantle the clamping device (8)
or mount on the opposite side of the fixed saw
table (17).
•
Move the machine head (5) to its upper posi-
tion.
•
Fasten the turntable (16) in 0° position.
•
Undo the locking screw (23). Use the handle
(1) to tilt the machine head (5) to the left until
the pointer (21) points to the required angle
on the scale (20).
•
Re-tighten the fixing screw (23).
•
Cut as described in section 7.1.
7.4 Miter cut 0°- 45° and turntable 0°-
45° (Fig. 1-3, 15)
The crosscut saw can be used to make miter cuts
to the left of 0°- 45° in relation to the work face
and, at the same time, 0° - 45° to the left or 0° -
45° to the right in relation to the stop rail (double
miter cut).
•
If required, dismantle the clamping device (8)
or mount on the opposite side of the fixed saw
table (17).
•
Move the machine head (5) to its upper posi-
tion.
•
Release the turntable (16) by slackening the
locking grip (13).
•
Press the latched position lever (12). Turn the
turntable (16) and scale pointer (14) to the
desired angular setting on the scales (15) and
lock into place with the locking grip (13).
•
Undo the locking screw (23) and use the
handle (1) to tilt the machine head (5) to the
left until it coincides with the required angle
value (in this connection see also section 7.3).
•
Re-tighten the fixing screw (23).
•
Cut as described under section 7.1.
7.5 Limiting the cutting depth (Fig. 16)
•
The cutting depth can be infinitely adjusted
using the screw (27). To do this loosen the
knurled nut on the screw (27). Move the stop
for the cutting depth limiter (28) to the outside.
Turn the screw (27) in or out to set the requi-
red cutting depth. Then re-tighten the knurled
nut on the screw (27).
•
Check the setting by completing a test cut.
7.6 Sawdust bag (Fig. 2)
The saw is equipped with a debris bag (22) for
sawdust and chips.
The debris bag (22) can be emptied by means of
a zipper at the bottom.
7.7 Changing the saw blade
(Fig. 1, 17-20)
Remove the power plug!
Important.
Wear safety gloves when changing the
saw blade. Risk of injury.
•
Swing up the machine head (5). Use the sa-
fety pin (25) to lock the machine head in this
position.
•
Press the release lever (3). Swing up the saw
blade guard (6) to the point where the recess
in the saw blade guard (6) is above the flan-
ge bolt (31).
•
Press the saw shaft lock (4) with one hand.
With the other hand insert the Allen key (c) in
the flange bolt (31).
•
Firmly press the saw shaft lock (4) and slowly
rotate the flange bolt (31) in clockwise direc-
tion. The saw shaft lock (4) engages after no
Anl_4300685.indb 50Anl_4300685.indb 50 08.10.12 17:2308.10.12 17:23
… 50 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PKS 1700 B2 - IAN 79729 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PKS 1700 B2 - IAN 79729 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 3,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PKS 1700 B2 - IAN 79729

Parkside PKS 1700 B2 - IAN 79729 User Manual - French, Italian - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info