Manual Parkside PKS 1500 A1 - IAN 102787 (page 11 of 52) (English, German, Dutch, French)

595350

Zoom out

Zoom in

1/52

6 GB/IE

Safety instructions for handling batteries

1 Always make sure that the batteries are inserted

with the correct polarity (+ and –), as indicated on

the battery.

2 Do not short-circuit batteries.

3 Do not charge non-rechargeable batteries.

4 Do not overcharge batteries!

5 Do not mix old and new batteries or batteries of

different types or manufacturers! Replace an entire

set of batteries at the same time.

6 Immediately remove used batteries from the device

and dispose of them properly!

7 Do not allow batteries to heat up!

8 Do not weld or solder directly on batteries!

9 Do not dismantle batteries!

10 Do not allow batteries to deform!

11 Do not throw batteries into re!

12 Keep batteries out of the reach of children.

13 Do not allow children to replace batteries without

supervision!

14 Do not keep batteries near re, ovens or other sour-

ces of heat. Do not use batteries in direct sunlight

or store them in vehicles in hot weather.

15 Keep unused batteries in the original packaging

and keep them away from metal objects. Do not

mix unpacked batteries or toss them together! This

can lead to a short-circuit of the battery and thus

damage, burns or even the risk of re.

16 Remove batteries from the equipment when it will

not be used for an extended period of time, unless

it is for emergencies!

17 NEVER handle batteries that have leaked without

appropriate protection. If the leaked uid comes into

contact with your skin, the skin in this area should be

rinsed off under running water immediately. Always

prevent the uid from coming into contact with the

eyes and mouth. In the event of contact, please seek

immediate medical attention.

18 Clean the battery contacts and corresponding

contacts in the device prior to inserting the batteries.

m Residual risks

The machine has been built according to the state of

the art and the recognised technical safety require-

ments. However, individual residual risks can arise

during operation.

• Health hazard due to electrical power, with the use of

improper electrical connection cables.

• Furthermore, despite all precautions having been met,

some non-obvious residual risks may still remain.

• Residual risks can be minimised if the „safety instruc-

tions“ and the „Proper use“ are observed along with

the whole of the operating instructions.

• Do not load the machine unnecessarily: excessive

pressure when sawing will quickly damage the saw

blade, which results in reduced output of the machine

in the processing and in cut precision.

• When cutting plastic material, please always use

clamps: the parts which should be cut must always

be xed between the clamps.

• Avoid accidental starting of the machine: the opera-

ting button may not be pressed when inserting the

plug in an outlet.

• Use the tool that is recommended in this manual.

In doing so, your mitre saw provides optimal perfor-

mance.

• Hands may never enter the processing zone when the

machine is in operation. Release the handle button

and switch off the machine prior to any operations.

Commissioning

Prior to commissioning, observe the safety instruc-

tions in the operating instructions.

REMOVAL FROM THE PACKAGING

Remove the machine from its package, which protects it

during transport, without damaging the package in order

to be able to use it later for transporting the mitre saw for

long-term storage.

MOVING

Since the mitre saw is relatively small and light, its lo-

cation can be easily changed, even by a single person.

After locking the locking knob (26 - Fig. 4) in the bottom

position, lift the mitre saw by the handle (2 - Fig. 4).

TRANSPORT

If the machine must be transported, carry it by the hand-

le (2 - Fig. 4) and place it in the original packaging in

which it was supplied. In the process, make sure that it

is correctly positioned in the package (see arrows on the

package).

If possible, the load should be xed with ropes or secu-

ring belts in order to prevent shifting during the transport

or parts of the load from falling down.

POSITIONING/WORK STATION

Position the machine on a work bench or on a at base

so that the machine is supported as stably as possible.

When working with the machine, ergonomic factors

must be considered; the ideal height of the work table

or the base is reached when the base surface or the up-

per work surface is 90 to 95 cm above the ground. The

positioning of the machine must provide for at least 80

cm of clearance in all directions and in order to allow for

cleaning and repair work as well as necessary adjust-

ments in observance of safety conditions and with suf-

cient room to manoeuvre.

CAUTION: Position the machine in a zone which is

suitable in respect to the environmental conditions and

lighting. Never forget that the general environmental

conditions play an extremely important role in accident

prevention.

CONNECTION TO THE POWER SUPPLY

Make sure that the socket is in a good condition. We

would like to remind you that the power supply must be

connected to a magnetic-thermal circuit breaker which

protects all lines from short-circuits and overloading.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PKS 1500 A1 - IAN 102787 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,31 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PKS 1500 A1 - IAN 102787 Manual

Product: