684713

Parkside PKGA 40-Li A1 - IAN 313870 Manual

60
Zoom out
Zoom in
Previous page
1/310
Next page
60
GB IE
2. Release the nut ( 34) and remove
the chain wheel cover (
33).
3. Remove the old saw chain (
1).
The mounting and tensioning of the new
saw chain is described in the “Assembly”
chapter.
Servicing the blade bar
The blade bar has to be reversed every
8-10 operational hours in order to ensure
even wear (see the “Servicing and clea-
ning - rotating the blade bar” chapter”).
1. Switch off the device and remove the
batteries from the device.
2. Remove the chain wheel cover (
33),
the saw chain (
1) and the blade
bar (
35).
3. Check the blade bar (
35) for wear.
Remove burrs and straighten the guide
surfaces with a at le.
4. Clean the oil passage (
62) to en-
sure fault-free, automatic oiling of the
saw chain during operation.
5. Mount the blade bar, saw chain and
chain wheel cover and retighten the
saw chain (see the “Assembly” chap-
ter).
Turning the blade bar
1. Switch off the device and remove the
batteries.
2. Release the nut (34) and remove the
chain wheel cover (33).
3. Remove the chain wheel cover (33)
and the blade bar (35).
4. Turn the blade bar (35) once along its
horizontal axis.
5. Insert the saw chain (1) into the blade
bar groove. Place the saw chain (1)
into the chain sprocket (36).
6. Place the blade bar (35) and saw
chain (1) onto the rail bolts (37). When
the nose on the right below the guide
bolt (37) sits in the lower round recess
on the blade bar, the blade bar is
placed correctly. It is normal for the
saw chain (1) to sag.
7. Pre-tension the saw chain (1) by turning
the screw (38) to tension the chain in a
clockwise direction.
8. Put the chain wheel cover (33) back in
position. Tighten the chain wheel cover
nut (34).
Replacing the spool
1. Remove the rechargeable batteries.
2. Place the device on the ground in a
stable position.
3. Block the mounting spindle (
52)
using the hexagon socket wrench (
22) as depicted.
Screw the spool cap (17) clockwise
to the mounting spindle (
52).
4. Open the spool cap (17) by rmly
pressing the quick-release catch (57)
inwards on both sides of the spool cap
(17), and remove the spool cap cover.
5. Place the new spool (58) into the spool
cap cover (17) and insert the two ends
of the thread through the thread outlets
(59). Loosen the two thread ends from
the grooves (
61) on the spool.
6. Place the spool (58) inside the lid of
the spool cap (17) and reassemble the
lid and base.
7. Screw the spool cap (17) anticlock-
wise back onto the mounting spindle (
52). Remove the hexagon so-
cket wrench (
22).
8. Trim the thread line to approx. 15 cm.
… 60 …


Need help? Post your question in this forum.

Forumrules
1

Forum

parkside-pkga-40-li-a1---ian-313870

Reset search

  • Bonjour. Je recherche un arbre de transmission de 64 cm de long et de 5 MM de diametre avec les.bout carré sur 2 cm de long pour une perche multifonction tailles haies électriques parkside Submitted on 3-8-2022 at 21:32

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PKGA 40-Li A1 - IAN 313870 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PKGA 40-Li A1 - IAN 313870 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 5,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info