779750

Parkside PISG 120 A2 - IAN 331996 Manual

34
Zoom out
Zoom in
Previous page
1/137
Next page
34 GB/IE
the event a fault can be provided
by using a fault-circuit interrupter,
which is operated with a leakage
current of no more than 30 mA
and covers all mains-powered
devices in close proximity. The
fault-circuit interrupter must be
suitable for all types of current.
There must be means of rapid
electrical isolation of the welding
power source or the welding cir-
cuit (e.g. emergency stop device)
which are easily accessible.
When using welding devices
under electrically dangerous
conditions, the output voltage
of the welding device must be
greater than 113 volt when idling
(peak value). Based on the output
voltage this welding device may
be used in these conditions.
zWelding in tight spaces
When welding in tight spaces
this may pose a hazard through
toxic gases (risk of suffocation).
In tight spaces you may only
weld if there are trained individu-
als in the immediate vicinity who
can intervene if necessary. In this
case, before starting the welding
procedure, an expert must carry
out an assessment in order to
determine what steps are neces-
sary, in order to guarantee safety
at work and which precautionary
measures should be taken during
the actual welding procedure.
zTotal of open circuit
voltages
When more than one welding
power source is operated at the
same time, their open circuit
voltages may add up and lead to
an increased electrical hazard.
Welding power sources must
be connected in such a way
that the danger is minimised.
The individual welding power
sources, with their individual con-
trol units and connections, must
be clearly marked, in order to
be able to identify which device
belongs to which welding power
circuit.
zUsing shoulder straps
Welding must not take place
if the welding power source is
being carried e.g. with a shoul-
der strap.
This is intended to prevent:
The risk of losing your balance
if the lines or hoses which are
connected are pulled
Safety instructions
331996_Inverter_Schweissgeraet_PISG_120_A2_content_LB8.indb 34331996_Inverter_Schweissgeraet_PISG_120_A2_content_LB8.indb 34 17.12.2019 14:19:0817.12.2019 14:19:08
… 34 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PISG 120 A2 - IAN 331996 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PISG 120 A2 - IAN 331996 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 2.2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info