819957

Parkside PHSL 710 A1 - IAN 415845 Manual

34
Zoom out
Zoom in
Previous page
1/316
Next page
GB MT
34
A
Switching On and Off
Ensure that you are standing in a
rm position with both hands grip-
ping the hedge trimmer away from the
body. Ensure that the trimmer is in contact
with no other objects before switching on.
1. Make a loop in the end of the extensi-
on cable and suspend this in the cable
strain relief (18).
See Fig. for correct use of the
strain relief.
2. Connect the device to the mains voltage.
3. To switch on, hold the safety switch (15)
depressed and simultaneously press the
on/off switch (16). The hedge trimmer
will be run at maximum speed. You can
release the safety switch (15) again.
4. The equipment will switch off again
when you release on/off switch (16).
A
Working with the
Electric Hedge Trimmer
During cutting work, ensure that no
contact is made with objects, e.g.
such as wire fencing or main plant stems.
This may result in damage to the cutter bar.
• To avoid eye injuries, always wear the
supplied safety goggles while working
with the hedge trimmer (22).
• Always hold the equipment rmly in
both hands, with one hand on the rear
handle and the other on the front han-
dle (13). Thumbs and ngers must be
rmly around the handles.
• Check the shoulder strap (19) on a
pleasant position, which makes it easier
for you to hold the hedge trimmer.
• Switch off the equipment immedi-
ately in the event that the blades are
blocked by solid objects, pull out the
power plug then remove the object.
• Always work away from the mains
power outlet. Set the cutting direction
before starting work. Ensure that the
power cable is kept well away from
the working area. Never lay the cable
over the hedge, where it could easily
be caught up in the trimmer blades.
• Avoid overstraining the equipment dur-
ing work.
Pull out the power plug imme-
diately if the cable is dam-
aged, badly twisted or has been
completely cut through. Risk of elec-
tric shock!
A
Putting down the device
• Place the device on the ground with
the motor housing rst.
• The safety cutter bar (1) must be
placed on the ground without being
subjected to any pressure.
• Do not apply any static pressure what-
soever to the cutter bar (1).
E
Swivelling the Arm
Caution!
The gear box (2) becomes hot
during operation. There is a
risk of burns. Do not touch the
gearbox housing (2) or the
connecting point to the front
tubular shaft (6).
1. Release the indexing by pushing the
safety slide (14) forward.
2. The tubular shank can now optionally
be turned 45° / 90° to the right or the
left (see the scale on the device).
… 34 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PHSL 710 A1 - IAN 415845 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PHSL 710 A1 - IAN 415845 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 4.79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info