819957

Parkside PHSL 710 A1 - IAN 415845 Manual

33
Zoom out
Zoom in
Previous page
1/316
Next page
GB MT
33
of the device housing (11) and the
soft grip (27).
The dismantling takes place in reverse order.
Initial Operation
Do not use the equipment
without the hand guard.
Wear suitable clothing and work
gloves when working with the
equipment.
Ensure that the equipment is func-
tional before each use. The On/Off
switch and the safety switch must
not be held closed. They must switch
off the motor when on is released.
Should a switch be damaged, stop
working with the equipment. Ensure
that the mains voltage value match-
es the label on the equipment.
Note noise protection and local
specications. The use of the equip-
ment on certain days (e.g. Sundays and
national holidays), at certain times of day
(lunch times, night time quiet periods) or in
special areas (e.g. health resorts, clinics
etc.) is restricted or forbidden.
D
Swivelling Out the
Blade Beam
1. Hold the safety blade beam (1) on the
handle to adjust the blade beam (5).
2. Unlock the safety lever (3) and keep it
pressed.
3. By simultaneously exerting pressure on
the lock lever (4), you will loosen the
xation of the cutter bar (1).
4. The safety blade beam (1) can now be
swivelled out. Use the stop stages and
allow the stop lever (4) to click back in.
You can choose 9 stop stages.
5. Then, release the safety lever (3) again
and ensure that it latches back into its
initial position.
Attach the shoulder strap
Warning! Never wear the car-
rying strap diagonally across
your shoulders and chest: only wear
it on one shoulder to ensure you can
detach the device quickly from your
body in the event of danger.
Place the shoulder strap on one shoulder.
Attach the shoulder strap spring clip
(19) to the carrying eyelet (20) on the tubu-
lar shank of the device. Set the strap length
such that the spring clip on the shoulder
strap is roughly at the height of your hip.
Sliding the carrying eye
You can slide the carrying eye (20) to bet-
ter spread the weight of the device.
You may need to slide the soft grip (27)
by turning and sliding to achieve this.
1. Loosen both screws (28) with an Allen
key (4 mm).
2. Gently retighten the screws (28).
3. Place on the shoulder strap and attach
the device to the shoulder strap. (See
“Attaching the shoulder strap”)
4. Slide the carrying eye (20) until the
weight of the device is spread evenly.
5. Put the device down and tighten the
screws (28).
A
Removing the knife
guard
Press the knife guard (21) on the location
marked „Parkside“ and remove it.
… 33 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PHSL 710 A1 - IAN 415845 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PHSL 710 A1 - IAN 415845 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 4.79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info