679445
24
Zoom out
Zoom in
Previous page
1/34
Next page
PHP 500 D2
GB
MT
 21
and are aware of the potential
risks. Children must not play with
the appliance. Cleaning and user
maintenance tasks may not be car-
ried out by children unless they are
supervised.
To avoid potential risks, damaged mains cables
should be replaced by the manufacturer, their
customer service department or a similarly
qualified person.
Additional safety instructions for
glue guns
Children should be supervised to ensure that
they do not play with the appliance.
CAUTION! This appliance must be placed on
its stand when not in use.
Always protect the appliance from rain and
moisture. Water entering a power tool will
increase the risk of electric shock.
Do not misuse the power cord, e.g. to carry
or hang up the appliance, or to pull the plug
from the socket. Keep cord away from heat,
oil, sharp edges or moving parts. If the power
cord is damaged or severed during work, do
not touch the cord but rather pull out the power
plug. Damaged or entangled cords increase the
risk of electric shock.
Only for indoor use.
If you take a break of longer than 30 minutes,
pull out the power plug.
Allow the appliance to cool completely after
use and before storage.
Do not work on any material containing asbestos.
Avoid the risk of injury or fire as well as health
risks: RISK OF BURNS! The adhesive and the
nozzle reach a temperature of around 200°C. Do
not touch the nozzle or the glue. Do not allow hot
glue to come into contact with people or animals.
In case of contact with skin, rinse the affected part
in cold running water for a few minutes. Do not
attempt to remove the adhesive from the skin.
Always route the power cable towards the rear,
away from the appliance.
Do not pull back the glue stick!
Cut it off to store the device in the
carrying case.
Operation
Before use
Preparing the surfaces to be glued:
Do not use flammable solvents to clean the
surfaces to be glued.
The ambient temperature and the materials to
be bonded may not be colder than 5°C and
not warmer than 50°C.
The area to be glued must be clean, dry and
free of grease.
Smooth surfaces should be roughened before
gluing.
Quick-cooling materials such as steel should be
warmed a little to facilitate adhesion.
Select the desired nozzle
.
Using the appliance
Mains operation:
Connect the power cable
to the mains
connection of the glue gun (see fig. B). Insert
the power plug into the socket.
Fold down the plastic stand
. Put down the
appliance.
Push a glue stick into the feeder shaft
.
Allow the appliance to heat up for about
5 minutes. The appliance is now ready for use.
Battery operation:
Connect the power cable
to the mains
connection of the charger
. Insert the power
plug into the socket.
Place the glue gun into the charger
.
Push a glue stick into the feeder shaft
.
Allow the appliance to heat up for about
5 minutes. The appliance is now ready for use.
Repeat the heating phase if the glue is still too
thick or viscous.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PHP 500 D2 - IAN 304706 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PHP 500 D2 - IAN 304706 in the language / languages: English, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PHP 500 D2 - IAN 304706

Parkside PHP 500 D2 - IAN 304706 User Manual - German, Dutch, Danish, French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info