26 GB/IE
6.12 Residual risks
m CAUTION
Even if used correctly, it is not possible to exclude non-appar-
ent residual risks entirely.
• Injuries due to slipping on waste water.
• Injuries or property damage due to the high-pressure water
jet.
7. Technical data
Engine
Type DVO175
Displacement cm³ 173
Nominal output
at 3500 min-1
kW (PS) 3.3 (4.5)
Nominal speed min-1 3500+/-100
Fuel tank l 1.2
Fuel Petrol, unleaded
Fuel consumption
at full load
l/h 0.8 - 0.9
Oil volume - engine l 0.4
Oil type – engine SAE10W30
Spark plug F7RTC
Water connection
Hose diameter mm min. 12.7
Supply temperature
max.
°C 40
Supply pressure
max.
MPa (bar) 0.2 - 0.5 (2 - 5)
Pump
Working pressure MPa (bar) 17.9 (179)
Max. working
pressure
MPa (bar) 19.9 (199)
Flow rate l/min 8.7
Max. flow rate l/min 9.1
Opening temperature
thermal valve
°C 55 - 60
Inlet connection G 3/4 (EU)
Outlet connection M22x1,5
Dimensions and weight
Length x width x
height
mm 620x500x1040
Typical operating
weight
kg 22
Cleaning agents Only use cleaning agents
approved for high-pressure
cleaners.
Noise emission
Noise measurement value determined in accordance with EN
60335-2- 79. The A-rated noise level is typically as follows:
Sound pressure level LpA ..........................90 dB(A)
Uncertainty KpA ...............................................3 dB
Sound power level LWA ........................... 105 dB(A)
Uncertainty KWA ..............................................3 dB
Wear ear protection to prevent hearing damage!
Vibration values (vector total of three directions) determined in
accordance with EN 60335-2-79:
Hand spray gun handle
Vibration value ......................................1,62 m/s2
Centre hand spray gun
Vibration value ..................................... 2,27 m/s²
Uncertainty K ........................................ 0,85 m/s²
NOTE:
The vibration level specified in these instructions has been
measured in accordance with the standardised measuring pro-
cedure specified in EN 60335-2-79 and can be used to make
equipment comparisons. The specified vibration emission value
can also be used to make an initial exposure estimate.
m WARNING
• The vibration level varies in accordance with use and may
be higher than the value specified in these instructions in
some cases. There is a risk of underestimation of the vibra-
tion load if the appliance is used regularly in this manner.
To estimate the vibration load during a specific working
period accurately, periods during which the appliance is
switched off (or running, but not being used) must also be
taken into account. This can significantly reduce the vibra-
tion load over the total working period.
8. Unpacking
• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the packaging
and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport dam-
age.
• If possible, store the packaging until the warranty period
has expired.
m DANGER
The device and packaging materials are not toys! Children
must not be allowed to play with plastic bags, film and small
parts! There is a risk of swallowing and suffocation!
m WARNING
• Exercise caution when unpacking, transporting and stor-
ing due to the high weight of the machine. These activities
should be carried out by two people.
• Make sure that the appliance is standing on a level and
flat surface while unpacking, and during assembly, stor-
age as well as during operation, inspection, maintenance
and when at a standstill.
9. Attachment
9.1 Fitting the handle (Fig. 3)
Insert the bow-type handle (1) on the base frame of the device.
Press the two push buttons on the base frame and push the
bow-type handle (1) completely until it clicks into place.
