Manual Parkside PHD 150 E4 - IAN 280206 (page 9 of 74) (English, German, Dutch, Danish, French)

655516

9

Zoom out

Zoom in

Previous page

1/74

Next page

9

NI

IEGB

cable drum before use. Check the ca-

ble for damage.

• Before any work on the equipment,

during work breaks and in the case

of non-use, remove the plug from the

socket.

• The cross-section of the power sup-

ply cable must not be less than

2x2,5mm².

• Wear sturdy footwear to protect

against electric shock.

• To protect against electric shock, oper-

ate the equipment only in an upright

position.

Start-up

In keeping with current regulations a

pressure cleaner must never be oper-

ated off the drinking water mains

supply without a controllable back-

ow preventer. A suitable backow

preventer in conformity with

EN 12729 type BA must be used.

Water that has passed through a backow

preventer is classied as undrinkable.

A backow preventer is available in spe-

cialist shops.

• Employ an ordinary garden hose for

the water intake and ensure sufcient

length.

• Use the device on a domestic water

connection with an output of at least

450 l/h.

• Irrespective of the water pipe, you can

also use the device (for example, rain

barrel) through the integrated water

suction function. This function must only

be used with a suction hose with a l-

ter basket.

The device itself must not be immer-

sed in open water sources. There

is a risk of personal injury from an

electric shock.

Do not draw in any water from na-

tural accumulations. There is a risk

of contamination from backwashed

cleaning agent.

Setting up

1. Fold the handle after upwards until

it engages with a resistor. Insert the

crank of the reel (17) to the stop into

the hose drum. The handle clicks into

place. Fold out the handle of the crank.

It xed via a resistor.

If the crankshaft of the hose drum

(17) can not simply be pushed as

far as it will go, pull out the cranks-

haft of the hose drum (17) and turn

the crankshaft of the hose drum (17)

to a different position before retur-

ning it.

2. Slide the holder for mains cable

(14/15) and the jet gun holder (6)

onto the guides on the device housing.

3. Connect the high-pressure tting (jet

gun) (4) to the jet gun (1). Ensure that

the hose runs to the front, so as not to

impede the handle (20).

4. Connect the feed hose to the water

supply and allow water to escape from

the other end of the feed hose with no

bubbles, in order to expel the air from

the feed hose. Switch off the water tap.

5. Connect the feed hose with the help of

the quick connector for garden hose

adapter (21) with the water connection

coupling (11) and the water connec-

tion (12) on the device.

6. Connect to the spray gun (1) by insert-

ing and screwing in the jet pipe (9).

7. If the jet pipe (9) is mounted, connect

either the turbo dirt mill (10) or the

standard Vario nozzle (24) by screw-

ing in with the jet pipe (9).

1

Hi.
When I connect my pressure washer it will start and then stop. When I remove the unit from the lance water will be pumped through the lance but once you attach a spray gun it stops. Submitted on 11-5-2021 at 19:54
Reply Report abuse
Onko phd 150 e4 saatavana moottoria joka on tosi hiekko? Submitted on 30-9-2020 at 06:54
Reply Report abuse
Part no
2»pa66 +30gf« how do you remove off part 2 lance (lance has a yellow part to it)I need to get to nozzle Submitted on 6-4-2018 at 19:16
Reply Report abuse
unable to draw water into my parkside phd 150 e 4 pressure washer Submitted on 12-11-2017 at 15:42
Reply Report abuse
does the PHD 150 E4 contain a suction pump ie for connecting it to a water butt Submitted on 18-10-2017 at 15:44
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

Register

Register getting emails for Parkside PHD 150 E4 - IAN 280206 at:

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PHD 150 E4 - IAN 280206 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 1,06 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info