684703

Parkside PHA 12 A1 - IAN 312203 Manual

25
Zoom out
Zoom in
Previous page
1/184
Next page
25
IE
GB
Checking the charge status
of the battery
The battery charge indicator ( 2) signa-
lises the state of charge of the battery (
6) while the device is operating. Press and
hold the power button to view.
3 LEDs are on (red, yellow, green):
Battery charged
2 LEDs are on (red, yellow):
Battery partially charged
1 LED is on (red):
Battery needs to be charged
Charge the battery ( 6) when
only the red LED on the level indica-
tor is illuminated.
Working instructions
Work safely, giving due con-
sideration to the next steps!
Planing
Attention! Risk of kickback!
Make sure the planer is swit-
ched on before guiding it over
the workpiece to be machined.
· Secure the workpiece to be machined.
· Set the desired cutting depth.
· Place the device’s planer sole and
V-groove onto the workpiece.
· Switch on the device and guide it with
a uniform forward motion over the
workpiece to be machined.
Chamfering edges
The V-groove at the front of the planer sole
is for chamfering edges.
· Place the planer’s V-groove (
13) on
the edge of the workpiece and guide it
along the edge.
Maintenance and Care
Replacing planer blades
Always remove the recharge-
able battery before carrying
out work on the device.
Risk of injury!
Cutting hazard! Do not hold
the planer blade by its cutting
edges.
Two blades are installed in the planer
shaft. The blades have two cutting edges,
which can be turned around. Always use
and replace the blades in pairs. Do not
attempt to sharpen the blades!
Always change the blades one after
the other. In this way, you can use
the one that is still installed to guide
you during  tting.
Replacement blades can be purcha-
sed from customer service (see ‘Spa-
re parts/accessories’).
1. Unscrew the two nuts (15) with the
spanner (10).
2. Using the Allen key (9), turn the screws
(16) in a clockwise direction as far as
you need to in order to push the blade
(17) out of the blade holder (14).
Use a small piece of wood to push it out.
3. Clean the blade holder (14) if necessary.
4. Insert the turned-over blade or new bla-
de into the blade holder (14).
The groove in the blade must point in
the direction of the part of the planer
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PHA 12 A1 - IAN 312203 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PHA 12 A1 - IAN 312203 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 2,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info