576665
13
Zoom out
Zoom in
Previous page
1/99
Next page
13 GB/IE
General safety advice for electrical power tools / OperationGeneral safety advice for electrical power tools
RISK OF INJURY!
Switch the device off and allow it to come to a
standstill before you put it down.
Always keep the device
clean, dry and free of oil or grease.
Safety notices for chargers
This appliance can be used by children aged
from 8 years and above and persons with re-
duced physical, sensory or mental capabilities
or lack of experience and knowledge if they have
been given supervision or instruction concerning
use of the appliance in a safe way and under-
stand the hazards involved. Children shall not
play with the appliance. Cleaning and user
maintenance shall not be made by children
without supervision.
The charger is only suitable for
indoor use.
Q
Operation
Never use the device for a purpose for which it was
not intended or with non-original parts / accessories.
The use of tools or accessories other than those rec-
ommended in the operating instructions could lead
to you suffering an injury.
Q
Charging the battery pack
NOTE! A battery pack that has been unused for a
while or never been charged must be charged before
reuse or first use. The battery pack requires about
3–5 cycles before it can reach its full charge. The
charging process takes about 180 minutes.
CAUTION! RISK OF INJURY!
Always pull
out the mains plug (
mains adapter
10
) before
you
insert the battery pack into or take it out of
the charger.
Insert the battery pack
4
into the charging
cradle
9
. This can only be inserted with the
correct polarity.
Connect the adapter
10
to a mains socket.
The red charge level indicator
11
will light up as
long as the battery pack is being charged. Once
charging is completed the red charge level in-
dicator
11
will extinguish and the green charge
level indicator
11 a
will light up. The battery
pack
4
is ready for use.
CAUTION! Do not charge a battery pack for
a second time in close succession. There is a
danger of overcharging the battery pack.
Q
Inserting / removing the
battery pack into / out of the
drill / grinder
Inserting the battery pack:
Set the ON / OFF switch
5
to position “0”.
Insert the battery pack
4
into the drill / grinder
until it engages.
Removing the battery pack:
Pressing the battery pack buttons
3
at the
sides at the same time allows you to remove
the battery pack
4
.
Q
Reading off the battery status
The status or residual power is indicated as follows
in the battery-operated LED
2
whenever the appli-
ance is switched on:
RED / ORANGE / GREEN = maximum charge / power
RED / ORANGE = medium-level charge / power
RED = weak charge recharge battery
Q
Inserting or replacing
a tool / collet
Press the spindle lock
8
and keep it pressed.
Rotate the clamping nut
6
until the lock
engages.
Loosen the clamping nut
6
with the combina-
tion key
23
.
If a tool is already inserted, remove it.
First insert the tool you wish to use through the
clamping nut
6
before you insert it into the
collet
18
suitable for the tool shaft.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PFBS 10.8 A1 - IAN 102778 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PFBS 10.8 A1 - IAN 102778 in the language / languages: English, German, Dutch, Danish, French, Swedish, Finnish as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info