576665

Parkside PFBS 10.8 A1 - IAN 102778 Manual

12
Zoom out
Zoom in
Previous page
1/99
Next page
12 GB/IE
General safety advice for electrical power tools / OperationGeneral safety advice for electrical power tools
comes to a complete stop. Never att
empt
to remove the cut-off wheel from the
cut while the wheel is in motion other-
wise kickback may occur. Investigate and
take corrective action to eliminate the cause of
wheel pinching or snagging.
f) Do not restart the cutting operation in
the workpiece. Let the wheel reach full
speed and carefully re-enter the cut.
The wheel may bind, walk up or kickback if
the power tool is restarted in the workpiece.
g) Support panels or any oversized work-
piece to minimize the risk of wheel
pinching and kickback. Large workpieces
tend to sag under their own weight. Supports
must be placed under the workpiece near the
line of cut and near the edge of the workpiece
on both sides of the wheel.
h) Use extra caution when making a
“pocket cut” into existing walls or
other blind areas. The protruding wheel
may cut gas or water pipes, electrical wiring
or objects that can cause kickback.
Special safety advice for
working with wire brushes
a) Bear in mind that wire brushes lose
pieces of wire during normal use. Do
not overload the wires by applying too
much pressure. Flying pieces of wire can very
easily penetrate thin clothing and / or skin.
b)
Allow brushes to run at operating spe
ed
for at least one minute before using
them. During this time no one is to
stand
in front or in line with the brush. Loose
bristles or wires will be discharged during the
run-in time.
c) D
irect the discharge of the spinning wir
e
brush away from you. Small particles and
tiny wire fragments may be discharged at high
velocity during the use of these brushes and
may become imbedded in your skin.
Q
Safety advice applicable specif-
ically to cordless multi-grinders
When you use the drill / grinder wear the fol-
lowing protective equipment: safety glasses
and protective gloves.
CAUTION! RISK OF INJURY! The tool
continues to rotate after it has been switched
off! Avoid contact with rapidly rotating drill /
grinder components.
Securely support the work-
piece. Use clamps or a vice to grip the workpiece
firmly. This is much safer than holding it in your
hand.
RISK OF INJURY! Never
support yourself by placing your hands near or
in front of the device or the workpiece surface.
A slip can result in injury.
DANGER OF FIRE FROM FLYING
SPARKS!
Abrading metal creates flying sparks. For this
reason, always make sure that nobody is placed
in any danger and that there are no inflamma
ble
materials near the working area.
DUST HAZARD! Any
harmful / noxious dusts generated from machin-
ing represent a risk to the health of the person
operating the device and to anyone near the
work area.
Wear a dust mask!
NOXIOUS FUMES!
Ensure that there is adequate ventilation when
machining surfaces containing plastic or cov-
ered with paint, varnish etc.
Its use as a saw or the use of saw blades with
this device is prohibited.
Do not soak the materials or the surface you
are about to work on with liquids containing
solvents.
Avoid abrading paints containing lead or other
substances hazardous to health.
Do not machine materials containing asbestos.
Asbestos is a known carcinogen.
Avoid contact with moving sanding or grinding
tools.
Do not machine moist materials or damp sur-
faces.
NOTE! Do not allow the tool to come to a stand-
still by overloading it!
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PFBS 10.8 A1 - IAN 102778 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PFBS 10.8 A1 - IAN 102778 in the language / languages: English, German, Dutch, Danish, French, Swedish, Finnish as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info