595413

Parkside PDSS 310 A1 - IAN 96878 Manual

12
Zoom out
Zoom in
Previous page
1/94
Next page
12 GB/IE
After initial use / Maintenance / Cleaning and Care / Troubleshooting
Commissioning
First wrap a piece of Teflon tape (not included)
around the outer threads of the plug nipple
9
and the lubricator
11
(see fig. B).
Now screw the plug nipple
9
into the thread
of the lubricator
11
(see Figure C).
Tighten this connection with moderate force
and absolutely using pliers.
Now turn the combination of lubricator
11
and
plug nipple
9
into the connection thread
2
of the impact driver (see Fig. C).
Also retighten this connection with pliers.
Now press the air hose onto the plug nipple
9
using a little force, until the hose locks in.
ATTENTION! Be sure the air hose
is firmly connected. A loose hose
whipping about out of control pre
sents
a major hazard. Also ensure the two screw
connections between lubricator
11
, coupling
and machine are securely seated.
Adjusting the compressed air
Note: this device is designed for an operating
pressure of up to 6.3 bar and a compressor with
the minimum air flow specified in the technical spe-
cifications. When setting the air pressure, remember
the pressure drops by approx. 0.6 bar with a hose
length of 10 m and an inside diameter of 9 mm.
Only use filtered, lubricated and regulated
compressed air.
Adjusting the torque
Set the torque control
3
to the correct torque
by pressing it toward the housing and turning it
until it locks at the desired setting.
Be sure the operating pressure of the compres-
sor is between 5 and 6.3 bar.
Note: the ideal pressure is 6.3 bar. The maximum
torque cannot be reached at a pressure of only 5
bar or with insufficient air flow.
Setting
1 (low, min.)
2 (normal)
3 (high)
4 (extra high,
max.)
Initial use
Activate the trigger
4
to start the equipment.
Release the trigger
4
to deactivate the equip-
ment.
Changing rotation
ATTENTION! The device must come to a
complete standstill before changing the direc-
tion of rotation.
ATTENTION! A machine rotating in an unex-
pected direction can be dangerous. Always
pay attention and use care.
Note: The impact driver clockwise / counter-
clockwise rotation. Use the reverse switch
6
to change the direction of the impact driver.
Pull the bolt forward in the direction of the „F“
marking („Forward / Fasten“) for clockwise
operation. You can now e.g. tighten screws.
Push the bolt back towards the „R“ marking
(„Reverse / Release“) so it protrudes from the
back of the equipment to set to counter-clock-
wise mode. You can now e.g. loosen screws.
Correctly holding the
equipment
This equipment weighs 2.3 kg.
Hold the equipment with both hands to ensure
safe operation (see Fig. D and E).
96878_par_Druckluft-Schlagschrauber PDSS 310 A1_content_GB_IE_FI_SE_DK_BE.indd 12 23.04.14 15:54
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PDSS 310 A1 - IAN 96878 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PDSS 310 A1 - IAN 96878 in the language / languages: Danish, French, Swedish, Finnish as an attachment in your email.

The manual is 3,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PDSS 310 A1 - IAN 96878

Parkside PDSS 310 A1 - IAN 96878 User Manual - English, German, Dutch - 45 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info