Manual Parkside PDEXS 150 A1 - IAN 64578 (page 33 of 45) (English, Portuguese, Spanish)

595404

Zoom out

Zoom in

1/45

33 GB/MT

Before use

Selecting the Grinding Disc

Metal Removal and Surface:

The rate of metal removal and the surface quality

are determined by the grain size of the grinding disc.

lease note that corresponding grinding discs

with diﬀerent grain sizes should be used for

processing diﬀerent materials.

Changing sanding sheets

The air sander is ﬁtted with a hook and loop fastening,

which allows for quick and easy replacement of

sanding discs.

Lift the grinding disc at the side and pull it oﬀ

from the backing pad

in order to remove it.

Note: Before securing a new sanding sheet, re-

move all dust and dirt from the sander plate

Ensure that the openings in the sanding sheet

concur with the boreholes of the sanding plate

Dust / Swarf Removal by Suction

Please note the “Safety instructions” section.

Using the internal vacuum extraction

with dust collection device (see Fig. B):

Push the exhaust air hose

fully on to the

connection for dust extraction

. Put the open-

ing of the dust bag

over the free end of the

exhaust air hose

and fasten the dust bag

ﬁrmly in position.

Note: Empty the dust bag

in good time and

regularly to ensure optimum dust extraction. To

do this open the zip fastener on the underside

of the dust bag

Topping up the oil

In order for the air sander to have a long service life,

there must always be enough pneumatic oil in the

device.

You may ensure this in any of the

following ways:

Connect a service unit with an oiler to the

compressor.

Install a line oiler in the compressed air line or

at the compressed air device.

Put approx. 3–5 drops of pneumatic oil by

hand into the plug nipple

every 15 minutes

of operation.

Preparing for use

Connecting the compressed

air source

Note: The air sander must be operated using

cleaned and condensate-free compressed air only

and its maximum allowable working

pressure of

6.3 bar at the device must not be exceed

ed.

Note: The compressed air source must be ﬁtted

with

a (ﬁlter) pressure reducer so that the air pressure can

be regulated.

Connect the plug nipple

by a quick-release

coupler to the compressed air supply.

Switching on and oﬀ

Note: Always switch on the air sander before

bringing it into contact with the workpiece material.

Switching on the air sander:

Press the operator’s lever

fully down

(see Fig. C).

Set the speed using the speed control

Switching off the air sander:

Release the operator’s lever

After you ﬁnish work, disconnect the device

from the compressed air source.

Note: First disconnect the hose from the com-

pressed air source (compressor) and only then

disconnect the compressed air supply hose

from the device. This will ensure that the com-

pressed air supply hose does not wave around

in an uncontrolled manner.

Before use / Preparing for use

64578_par_Druckluft-Exzenterschleifer_content_LB5.indd 33 27.06.11 16:21

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PDEXS 150 A1 - IAN 64578 in the language / languages: English, Portuguese, Spanish as an attachment in your email.

The manual is 3,28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PDEXS 150 A1 - IAN 64578

Parkside PDEXS 150 A1 - IAN 64578 User Manual - German, Dutch, French, Italian - 37 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PDEXS 150 A1 - IAN 64578 Manual

Product: