Manual Parkside PDBS 6.2 A1 - IAN 43096 (page 35 of 39) (English, German, Dutch)

595286

Zoom out

Zoom in

1/39

35 GB

General safety rules

General safety rules / Before use / Start-up

If you experience numbness, tingling, pain or

whitening of the skin in your ﬁngers or hands,

stop using the nibbler or shear, tell your employer

and consult a physician.

Operate and maintain the nibbler or shear as

recommended in this instruction handbook, to

prevent an unnecessary increase in vibration.

Hold the tool with a light but safe grip, taking

account of the required hand reaction forces,

because the risk from vibration is generally gr

eater

when the grip force is higher.

Additional safety instructions

for pneumatic power tools

Air under pressure can cause severe injury:

– always shut oﬀ air supply, drain hose of air

pressure and disconnect tool from air supply

when not in use, before changing accessories

or when making repairs;

– never direct air at yourself or anyone else.

Whipping hoses can cause severe injury. Always

check for damaged or loose hoses and ﬁttings.

Cold air shall be directed away from hands.

Whenever universal twist couplings (claw cou-

plings) are used, lock pins shall be installed

and whipcheck safety cables shall be used

to safeguard against possible hose-to-tool or

hose-to-hose connection failure.

Do not exceed the maximum air pressure stated

on the tool.

Never carry an air tool by the hose.

General safety

instructions for compressed

air metal shears

Always wear safety gloves.

Be careful whilst working with the shears. Edges

created on the work piece can cause cuts.

If possible, already run the shears at full speed

when applying them. Otherwise sudden, jerky

movement could result if the shears catch when

starting up at the front, resulting in backlash.

Before use

Installation

The device itself is fully functional at delivery. Using

the device may possibly (unless already built in) re-

quire a coupler to be attached (note the information

under Technical Data for the correct ﬁt / size).

Wrap the coupler with Teﬂon tape (not included)

before screwing it into the compressed air unitn.

Wrap the tape as tightly as possible around

the thread. This will minimise the likelihood of

air leaking and optimise the work process.

Now screw the coupling into the compressed

air equipment.

Tighten the coupler into the compressed air unit

with a size 14 spanner using moderate force

(see Fig. A).

Adjusting the compressed air supply and

connections

Only use ﬁltered, lubricated and regulated com-

pressed air.

Apply the connection method on the compressed

air unit shown in Fig. B. This will increase the ef-

fectiveness and life of the tool.

Set your compressor to the device‘s operating

pressure speciﬁed under Technical Data. Please

note, on average the pressure for 10 m of hose

will decrease by about 0.5 bar.

Excessive pressure is dan-

gerous! Never exceed the speciﬁed pressure!

Add a few drops of oil for compressed air tools

or SAE 10–20 motor oil to the compressed air

onnection of the compressed air unit. Using othe

oil (esp. viscous) will result in malfunctions, dam-

age or even total loss of the device.

Start-up

Connecting the

compressed air tool

Verify the work piece is properly supported.

Connect the compressed air by pushing on the

coupler of the hose with some force (see Fig. C).

43096_par_Druckluft-Blechschere PDBS 6.2A1_content_DE_NL.indd 35 28.05.14 16:57

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PDBS 6.2 A1 - IAN 43096 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 2,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PDBS 6.2 A1 - IAN 43096 Manual

Product: