Manual Parkside PBSG 95 B1 - IAN 108189 (page 9 of 45) (English, German, Dutch, Swedish, Finnish)

595310

Zoom out

Zoom in

1/45

9 GB/IE

General safety advice / Use

Make sure that the grinding tools are

appropriate in line with the instructions

of the manufacturer.

Check the grinding stone before using

it; do not use any broken, cracked or otherwise

damaged goods.

Make sure that a grinding tool is correct-

ly fitted and fastened before using it.

Place the grinder in a safe place and allow it

to run idly for 30 seconds. Stop it immediately if

considerable oscillations occur or if defects are

observed. If this occurs, check the machine to

ﬁnd out the cause.

Original accessories /

Attachments

Use only the accessories and attachments

detailed in the operating instructions.

The use of inserted tools or accessories other

than those recommended in the operating in-

structions could lead to you suﬀering an injury.

Use

Sharpening a drill

NOTE: Badly damaged drills should ﬁrst be coarsely

sharpened on a sharpening block.

Fully lower the sharpening stone. To do this turn

the rotary switch

in the DOWN direction

as far as it will go.

Insert the drill into the smallest suitable drill

guide

on the drill sharpener. The exact size

(Ø) of each drill guide

is shown by the ad-

jacent lettering (3 to 10).

Press the ON / OFF switch

into position “I”

to switch on the device.

Turn the rotary switch

in the UP direction

until you hear a grinding noise.

NOTE: The rotary switch

controls the posi-

tion of the sharpening stone in the sharpening

head housing and therefore the pressure of the

sharpening stone against the drill. The further

you turn the rotary switch

in the UP direction

the greater the pressure. Ensure that you do not

turn the sharpening stone too far up. Otherwise

the sharpening stone could strike the housing.

Turn the drill under slight pressure loosely and

quickly to and fro between the left and right stops

about 10 times (with small drills about 5 times).

Pull the drill out, turn it through 180° (horizon

tally)

and insert it again until it meets the sharpening

stone.

If necessary repeat whole process until both

cutting edges of the drill are sharp. Polish so the

angle (

) between the two cutting edges (b) is

118°. The two cutting edges (b) must have the

same angle to the drilling axle (a) and have

the same length so the drill runs centred (see

ﬁgures below).

(b)(b)

(a)

=118°

Press the ON / OFF switch

into position “0”

to switch oﬀ the device.

Replacing the

sharpening stone

RISK OF INJURY! Before you

carry out any work on the device, always pull the

mains plug out of the mains socket. Replace the

sharpening stone if it is worn out or damaged

(deteriorating, irregular sharpening performance,

broken stone). A Phillips screwdriver is required for

this step.

Screw the three screws

out of the sharpening

head cover

and remove the cover

, refer

to Fig. A.

Take out the sharpening stone

Clamp the sharpening stone

in a vice. Re-

lease the threaded connection

, which holds

the sharpening stone

on to the sharpening

stone holder

, using a 23 mm open spanner

or a wrench socket, see Fig. B.

General safety advice

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PBSG 95 B1 - IAN 108189 in the language / languages: English, German, Dutch, Swedish, Finnish as an attachment in your email.

The manual is 0,99 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PBSG 95 B1 - IAN 108189

Parkside PBSG 95 B1 - IAN 108189 User Manual - French - 28 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PBSG 95 B1 - IAN 108189 Manual

Product: