595429
24
Zoom out
Zoom in
Previous page
1/28
Next page
21
PBH 1500 A1
GB
Appliance-specifi c safety instructions
for hammer drills
Wear ear protectors. Exposure to
noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
Hold power tool by insulated gripping surfac-
es, when performing an operation where the
cutting accessory may contact hidden wiring
or its own cord. Cutting accessory contacting
a “live” wire may make exposed metal parts of
the power tool “live” and could give the opera-
tor an electric shock.
Wear a dust mask.
WARNING! TOXIC DUST!
Working with harmful/toxic dusts results in
health hazards for the person operating the
appliance and for other persons in the area.
ATTENTION – SERVICE LINES! DANGER!
Take steps to ensure that you do not hit any
service lines (electricity, gas, water) when
working with the electric tool. If necessary,
check with a service line detector before you
start to cut or drill into a surface.
Original accessories/additional
equipment
Only use the accessories and additional
equipment that are specifi ed in the operat-
ing instructions and are compatible with the
appliance.
Initial operation
Additional handle
NOTE
For safety reasons, you should only use this
appliance with the additional handle
attached.
Remove the additional handle by turning it
clockwise direction.
Turn the additional handle to the desired
position.
Fix the additional handle in the new position
by turning it anti- clockwise.
Depth stop
Open the wing screw .
Insert the depth stop into the additional
handle
.
Ensure that the toothing on the depth stop is
facing upwards.
Pull the depth stop out far enough for the
distance between the tip of the drill and the tip
of the depth stop to correspond with the
required drilling depth.
Re-tighten the wing screw afterwards.
Tool/chuck:
Pull the locking sleeve backwards and insert
the tool/chuck in the tool holder .
Release the locking sleeve . This locks the
holder. Check that the tool is properly locked by
pulling it. The system has radial play because of
the design.
Removing tool/chuck:
Pull the locking collar on the tool backwards.
NOTE
Tighten the drill in the wheel-rim chuck at the
same time. To do this, apply the chuck key to all
the 3 positions on the wheel-rim chuck and
tighten the tool (e.g. drill) at the same time.
WARNING!
Do not use the wheel-rim chuck for ham-
mer drilling or chiselling!
IB_35391_PBH1500A1_LB1.indb 21IB_35391_PBH1500A1_LB1.indb 21 28.05.14 16:3528.05.14 16:35
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PBH 1500 A1 - IAN 35391 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PBH 1500 A1 - IAN 35391 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 3,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PBH 1500 A1 - IAN 35391

Parkside PBH 1500 A1 - IAN 35391 User Manual - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info