Manual Parkside PAKSP 20-Li A1 - IAN 308540 (page 23 of 85) (English, German, Dutch, French, Polish)

796085

Zoom out

Zoom in

1/85

GB│IE │ 19 ■

PAKSP 20-Li A1

ATTENTION!

♦ If the red control LED * ﬂashes, the battery pack 5 has overheated

and cannot be charged.

♦ If the red and green control LEDs *) both ﬂash, this means that

the battery pack 5 is defective.

♦ Push the battery pack 5 into the appliance.

■ Never recharge a battery pack5again immediately after rapid

charging. There is a risk that the battery pack will overheat and this

will reduce the lifespan of the battery.

♦ Switch oﬀ the battery charger for at least 15 minutes between

successive charging sessions. Also disconnect the power plug from

the mains power socket.

Checking the battery charge level

♦ To check the battery status, press the battery charge level button.

The status will be shown on the battery display LED 2 as follows:

RED/ORANGE/GREEN = maximum charge

RED/ORANGE = medium charge

RED = low charge – charge the battery

Setting up the appliance

Always provide a stable set-up location for the appliance. Fix the appliance

using suitable bolts (not included in delivery) to a ﬂat, stable base. Use the

drill holes+ for this purpose.

NOTE

► In exceptional cases, you can position the baseplate on a solid support

for this purpose.

Transport

NOTE

► Only transport the appliance with the transport restraint # in place

and use the carrying handle /.

Removing transport restraint

♦ Apply a little pressure to the handle and pull out the transport

restraint# as far as it will go. The motor unitcan now be moved

upwards.

Inserting transport restraint

♦ First, press down the release button 0, then the handle . Then push

the transport restraint#into the appliance. The motor unit is now

ﬁxed in place.

Check that the blade guard is functioning correctly

WARNING! RISK OF INJURY!

Always switch the appliance oﬀ and remove the battery

before carrying out any work on the appliance.

■ Make sure that all moving parts of the blade guard. move freely

without jamming. All devices that cover the saw blade must work

properly.

♦ First, press down the release button 0, then the handle . Allow the

blade guard . to slide completely upwards.

♦ When you release the handle, the blade guard. must move freely

back to its starting position.

WARNING!

► When the handle  is released, the saw also springs back to its

starting position. Make sure that neither your hands or other parts

of your body are within the swivel range of the saw.

Fitting/changing the saw blade

WARNING!

► Always remove the battery pack 5 before changing the saw

blade6!

► The arrow on the saw blade 6 must correspond to the

arrow showing the direction of rotation (running direction shown on

the appliance).

♦ Press the release button0 and slide the blade guard.upwards.

Hold the blade guard. ﬁrmly with one hand. Make sure that the

mounting screw , is accessible. You can now let go of the release

button 0.

♦ Press the spindle lockall the way down with the same hand and

hold it in this position. If necessary, rotate the saw blade6with the

other hand until this is possible.

♦ Use the supplied hex keyto undo the mounting screw,.

♦ Remove the clamping ﬂange (external)and the saw blade6.

♦ Insert the new saw blade.

♦ Proceed in reverse order in order to reassemble the appliance to a

usable condition.

♦ Check whether all the fastening elements are correctly ﬁtted.

NOTE

► Ensure that the saw blade6can be rotated freely.

► Switch the appliance on for around 60 seconds to check that there are

no unusual vibrations. If this is not the case, you should check that the

saw blade6 is ﬁtted correctly.

Fitting the workpiece rest

♦ Loosen the respective screw  for the workpiece rest with a standard

Phillips screwdriver (not supplied).

♦ Push the workpiece rest  as far as possible into the corresponding

drill holes %.

♦ Retighten the screw  for the workpiece rest. Make sure that the

workpiece rest remains horizontal.

♦ Proceed in the same way on the other side.

Fitting the tensioning clamps

♦ Loosen the respective clamping screw$and insert the shaft of the

tensioning clamp 1 into the hole. Insert the shaft of the tensioning

clamp1 only so far into the hole so that the adjustable fence 3 can

move freely.

♦ Retighten the clamping screw$.

♦ Proceed in the same way on the other side.

Clamping the workpiece

♦ Place the workpiece under the respective tensioning clamp 1.

♦ Press the workpiece against the fence.

♦ First undo the setting screw for the tensioning clamp17aand adjust it

to ﬁt the workpiece. Then retighten the setting screw for the tensioning

clamp 17a .

♦ Afterwards, tighten the threaded rod& by turning it clockwise.

♦ To release the workpiece, turn the threaded rod &anticlockwise.

NOTE

► Long and heavy workpieces must be underlaid or supported at the

free end to ensure stability.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PAKSP 20-Li A1 - IAN 308540 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 2.21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PAKSP 20-Li A1 - IAN 308540 Manual

Product: