722879
73
Zoom out
Zoom in
Previous page
1/82
Next page
GB
- 73 -
For the protection of the operator it is essential to
specify safety measures which are based on an
estimate of the exposure during the actual condi-
tions of use (all stages of the operating cycle must
be considered, e.g. times in which the electric
tools are switched off and times in which the tool
is switched on but operates without load).
Residual risks
Even if you use this electric power tool
in accordance with instructions, certain
residual risks cannot be rules out. The fol-
lowing hazards may arise in connection
with the equipment’s construction and
layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
6. Before starting the
equipment
Be sure to read the following information before
you use your cordless screwdriver for the fi rst time:
1. Charge the battery pack with the charger
supplied. An empty battery pack requires a
charging period of approximately one hour.
2. Only ever use sharp drill bits and screwdriver
bits which are suitable for the purpose and in
faultless condition.
3. Always check for concealed electric cables
and gas and water pipes when drilling and
screwing in walls.
7. Operation
7.1 Charging the LI battery pack (Fig. 2-3)
The battery is protected from exhaustive dischar-
ge. An integrated protective circuit automatically
switches off the equipment when the battery is fl at.
In this case the bit chuck will cease to turn.
Warning! Do not press the ON/OFF switch any
more if the protective circuit has actuated. This
may damage the battery.
1. Remove the battery pack (5) from the handle,
pressing the pushlock buttons (6) on the left
and right sides to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(11) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Insert the battery pack (5) into the battery
charger (11).
4. In section 10 „Charger indicator“ you will
nd a table with an explanation of the LED
indicator on the charger.
If the battery pack fails to become charged, ple-
ase check
whether there is voltage at the socket-outlet
whether there is proper contact with the char-
ging contacts in the battery charger (11).
If the battery still fails to become charged, please
return
the charger and charging adapter
the battery pack
to our Customer Service Department.
To ensure that the LI battery pack provides long
service you should take care to recharge it
promptly. You must recharge the battery pack
when you notice that the power of the cordless
screwdriver drops.
Anl_4513640.indb 73Anl_4513640.indb 73 27.11.12 13:4927.11.12 13:49
73


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PABSW 10.8 A1 - IAN 86583 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PABSW 10.8 A1 - IAN 86583 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info