Manual Parkside MPKZ 2000 A1 - IAN 315340 (page 11 of 68) (English, German, Dutch, French)

706349

Zoom out

Zoom in

1/68

6 GB/IE/NI

c) The workpiece must be stationary and clamped

or held against both the fence and the table.

Do not feed the workpiece into the blade or

cut “freehand” in any way. Unrestrained or moving

workpieces could be thrown at high speeds, causing injury.

d) Push the saw through the workpiece. Do not

pull the saw through the workpiece. To make

a cut, raise the saw head and pull it out over

the workpiece without cutting, start the motor,

press the saw head down and push the saw

through the workpiece. Cutting on the pull stroke is

likely to cause the saw blade to climb on top of the work-

piece and violently throw the blade assembly towards the

operator.

e) Never cross your hand over the intended line of

cutting either in front or behind the saw blade.

Supporting the workpiece “cross handed” i.e. holding the

workpiece to the right of the saw blade with your left hand

or vice versa is very dangerous.

f) Do not reach behind the fence with either hand

closer than 100 mm from either side of the saw

blade, to remove wood scraps, or for any other

reason while the blade is spinning. The proximity

of the spinning saw blade to your hand may not be obvi-

ous and you may be seriously injured.

g) Inspect your workpiece before cutting. If the

workpiece is bowed or warped, clamp it with

the outside bowed face toward the fence. Al-

ways make certain that there is no gap be-

tween the workpiece, fence and table along

the line of the cut. Bent or warped workpieces can

twist or shift and may cause binding on the spinning saw

blade while cutting. There should be no nails or foreign

objects in the workpiece.

h) Do not use the saw until the table is clear of all

tools, wood scraps, etc., except for the work-

piece. Small debris or loose pieces of wood or other ob-

jects that contact the revolving blade can be thrown with

high speed.

i) Cut only one workpiece at a time. Stacked multiple

workpieces cannot be adequately clamped or braced and

may bind on the blade or shift during cutting.

j) Ensure the mitre saw is mounted or placed on

a level, ﬁrm work surface before use. A level and

ﬁrm work surface reduces the risk of the mitre saw becom-

ing unstable.

k) Plan your work. Every time you change the

bevel or mitre angle setting, make sure the

adjustable fence is set correctly to support the

workpiece and will not interfere with the blade

or the guarding system. Without turning the tool

“ON” and with no workpiece on the table, move the saw

blade through a complete simulated cut to assure there will

be no interference or danger of cutting the fence.

l) Provide adequate support such as table exten-

sions, saw horses, etc. for a workpiece that is

wider or longer than the table top. Workpieces

longer or wider than the mitre saw table can tip if not se-

curely supported. If the cut-oﬀ piece or workpiece tips, it

can lift the lower guard or be thrown by the spinning blade.

m) Do not use another person as a substitute for a

table extension or as additional support. Unsta-

ble support for the workpiece can cause the blade to bind

or the workpiece to shift during the cutting operation pull-

ing you and the helper into the spinning blade.

n) The cut-oﬀ piece must not be jammed or pressed

by any means against the spinning saw blade.

If conﬁned, i.e. using length stops, the cut-oﬀ piece could

get wedged against the blade and thrown violently.

o) Always use a clamp or a ﬁxture designed to

properly support round material such as rods

or tubing. Rods have a tendency to roll while being cut,

causing the blade to “bite” and pull the work with your

hand into the blade.

p) Let the blade reach full speed before contact-

ing the workpiece. This will reduce the risk of the work-

piece being thrown.

q) If the workpiece or blade becomes jammed,

turn the mitre saw oﬀ. Wait for all moving parts

to stop and disconnect the plug from the power

source and/or remove the battery pack. Then

work to free the jammed material. Continued

sawing with a jammed workpiece could cause loss of con-

trol or damage to the mitre saw.

r) After ﬁnishing the cut, release the switch, hold

the saw head down and wait for the blade to

stop before removing the cut-oﬀ piece. Reaching

with your hand near the coasting blade is dangerous.

s) Hold the handle ﬁrmly when making an incom-

plete cut or when releasing the switch before

the saw head is completely in the down posi-

tion. The braking action of the saw may cause the saw

head to be suddenly pulled downward, causing a risk of

injury.

Safety Instructions for the handling of saw blades

1 Do not use damaged or deformed saw blades.

2 Do not use any insertion tools with cracks. Sort out cracked

insertion tools. Repairs are not permitted.

3 Do not use saw blades made of high speed steel.

4 Check the condition of the saw blades before using the

sliding compound mitre saw.

5 Make sure that a suitable saw blade for the material to

be cut is selected.

6 Only use saw blades recommended by the manufacturer.

Saw blades designed to cut wood and similar materials

must comply with EN 847-1.

7 Do not use saw blades made of high-speed alloy steel

(HSS steel).

8 Only use saw blades for which the maximum permissible

speed is not lower than the maximum spindle speed of the

sliding compound mitre saw and which are suitable for

the material to be cut.

9 Observe the saw blade direction of rotation.

10 Only insertion the saw blade if you have mastered their

use.

11 Observe the maximum speed. The maximum speed speci-

ﬁed on the insertion tool may not be exceeded. If speciﬁed,

observe the speed range.

12 Clean grease, oil and water oﬀ of the clamping surfaces.

Parkside mpkz2000...when loosening saw blade Allen nut is it turned clockwise or anticlockwise Submitted on 19-2-2022 at 10:05
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside MPKZ 2000 A1 - IAN 315340 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,81 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside MPKZ 2000 A1 - IAN 315340 Manual

Product: