464975
9
Zoom out
Zoom in
Previous page
1/11
Next page
7 UK
or the relevant service centre.
· Do not operate the device if it is damp and do
not use it in a damp environment.
· If you use the device outdoors, always connect
it through a residual current device with a
maximum trip current of 30 mA.
If using an extension lead, always use one that
is approved for outdoor use.
· Always work with the mains lead leading away
from the rear of the device.
To avoid danger of injury and
hazards to health:
·
Wear protective glasses. Pieces of
material may split off the workpiece
and become projectiles. This could cause injury.
· Do not work on moistened materials or damp
surfaces.
· Do not soak the materials or the surface you
are about to work on with liquids containing
solvents. The heat generated during scraping
can give rise to poisonous vapours or gases
that are hazardous to health.
· Secure the workpiece by holding it in a clamp
or vice, otherwise the workpiece cannot be
securely held in place and could cause injury.
· Do not work on materials containing asbestos.
· When working, always hold the device se-
curely with both hands (see Fig. B).
Never support yourself by placing your hands
near or in front of the device or the workpiece
surface. You could be injured if anything slips.
· Danger! The sharp edges of the tools could
cause injury.
·
Wear
protective gloves.
· Caution! Keep children away from the mains
lead and do not allow them to use the device.
Children often underestimate the dangers as-
sociated with electrical equipment.
Using the device safely:
· If danger arises, pull the mains plug immedi-
ately out of the mains socket.
· Never use the device for a purpose for which it
was not intended.
· Handle the device carefully and treat it with
respect. Always keep the device clean, dry and
free of oil or grease.
· Remain alert at all times! Always watch what
you are doing and proceed with caution. Do
not use the device if you cannot concentrate or
you are feeling unwell.
í Before use
í Quick-change tool holder
½ Danger! The sharp edges of the tools could
cause injury.
½ The choice of tool depends on the intended
task. The supplied accessories are suitable for
the most common tasks (see fi gures C, D, E
and F). Carry out a short test to determine the
best tool for the task.
1. Press the tool lock
T
backwards into the
“Unlock” position.
2. Push the tool attachment into the tool holder
R
until it reaches the stop.
3. Lock the tool attachment in place and press
the tool lock
T
forwards into the “Lock” posi-
tion.
½ Make sure you fi t the tool the right way round.
The inside of the curve on the shank/working
edge of the tool attachment
E
must point
downwards.
í First use
The mains voltage at the mains socket must match
that shown on the rating plate on the device.
Devices marked with 230 V can also be operated
at 220 V.
Attention! When using the device, never allow the
ventilation slots to be covered.
Safety/Before Use/First use
Manual_UK_Inhalt.indd 7Manual_UK_Inhalt.indd 7 30.06.2005 10:26:59 Uhr30.06.2005 10:26:59 Uhr
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside KH 3113 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside KH 3113 in the language / languages: English as an attachment in your email.

The manual is 0,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside KH 3113

Parkside KH 3113 User Manual - German - 11 pages

Parkside KH 3113 User Manual - Dutch, French, Italian - 21 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info